Veritas™ 5340 Appliance Hardware Installation Guide
- Hardware overview
- Supported software
- 5340 compute node and 5U84 storage shelves
- 5340 compute node and storage shelf power requirements
- 5340 compute node disk drives
- 5340 compute node control panel
- 5340 compute node rear panel
- 5U84 storage shelf drawers and disk drives
- 5U84 storage shelf control panel
- 5U84 storage shelf rear panel
- 5U84 storage shelf RAID controller
- 5U84 storage shelf Expansion module
- Cables and connectors
- Preinstallation requirements
- Hardware installation procedures
- Overview
- Installing a storage shelf
- Installing disk drives into a full-capacity storage shelf
- Installing disk drives and blanks into a half-capacity storage shelf
- Installing SFPs into the RAID controller
- Installing the compute node rack rails
- Installing the compute node into a rack
- Connecting the hardware to one node
- Connecting the hardware to two nodes
- Connecting NetBackup nodes to the network
- Connecting Flex nodes to the network
- Connecting the power cords to the hardware
- Turning on the hardware and verifying operation
- Configuring the IPMI port from the NetBackup Appliance Shell Menu
- Accessing and using the Veritas Remote Management interface
- Appendix A. Adding Expansion Storage Shelves to an operating appliance that does not have any Expansion shelves
- Appendix B. Adding Expansion Storage Shelves to an operating appliance that has at least one operating Expansion shelf
- Overview
- Turning off the existing hardware
- Installation instructions
- Connecting one Expansion shelf to a system that has one existing Expansion shelf
- Connecting two Expansion shelves to a system that has one existing Expansion shelf
- Connecting one Expansion shelf to a system that has two existing Expansion shelves
- Appendix C. Configuring the disk space for new NetBackup Expansion Storage Shelves
- Appendix D. Configuring the disk space for new Flex Expansion Storage Shelves
Dimensions and determining rack locations
Physical specifications for the compute node include the following.
Each node is two rack units (2RU) high.
Node measurements are listed below.
Height: 21.97cm (8.65")
Width: 48.26cm (19")
Length/depth: 79.38cm (31.25")
The compute node rails are extensible to 813mm (32in). This distance is the maximum depth that is allowed between rack posts.
Physical specifications for the 5U84 storage shelves include the following.
Each storage shelf is 5RU high.
Storage shelf measurements are listed below.
Height: 22.23cm (8.75")
Width: 48.26cm (19")
Length/depth: 93.35cm (36.75") from the rear of the front flanges to the extreme rear of the storage shelf chassis.
Note:
The 5U84 storage shelf is longer than a standard IEC-compliant rack. Be sure that your rack cabinet and Power Distribution Units accommodate the length of the storage shelves.
The storage shelf rails measure 71.3cm to 88.4cm (28" to 34.8") in length. Be sure that your rack accommodates this distance from the inside of the front post to the inside of the rear post. Plan for additional space to accommodate power strips, power cords, and other cables.
When you plan the installation be sure to allocate enough space for all of the hardware.
A typical installation has the storage shelves on the bottom and the compute node(s) at the top.
To help you identify RU spacing, many rack manufacturers use a system of lines and sequential numbers starting at the bottom of the rack. The front and the rear of the rack are marked the same to ensure that the rails are installed straight and level. One RU has three holes. The holes for one RU are typically marked with a line below the bottom hole and another line at the top hole.
Use the rack templates to determine the mounting locations for all devices.
To determine rack locations for the hardware
- Determine the total number of rack units (RUs) that you need as follows:
One compute node (2RU) and one storage shelf (5RU) require 7RUs of height in the rack.
One compute node (2RU) and two storage shelves (5RU each) require 12RUs of height in the rack.
One compute node (2RU) and four storage shelves (5RU each) require 22RUs of height in the rack.
- Use the rack templates to determine RU locations.
- Fold the compute node templates at the horizontal yellow lines.
- Use the following graphics to determine where pins and screws for the storage shelves fit into the rack.
The front of each rail includes four pins that insert into the rear of the front rack post. One screw fits into the middle hole of the middle RU.
The rear of each rail includes four pins that insert into the inside of the rear rack post. Two screws insert into the front of the rear rack post. The screws install into the middle hole in the first and the fifth RU.
- Record the rack positions to help you locate them easily when mounting the hardware.
