Veritas NetBackup™ SAN Client and Fibre Transport Guide

Last Published:
Product(s): NetBackup (8.1.1, 8.1)
  1. Introducing SAN Client and Fibre Transport
    1.  
      About NetBackup SAN Client and Fibre Transport
    2.  
      About Fibre Transport
    3.  
      About Fibre Transport media servers
    4.  
      About SAN clients
    5.  
      About the Fibre Transport Service Manager
    6.  
      About NetBackup Release Notes
  2. Planning your deployment
    1.  
      Planning your SAN Client deployment
    2.  
      About SAN Client best practices
    3.  
      SAN Client operational notes
    4. About SAN Client storage destinations
      1.  
        About SAN Client disk storage destinations
      2. About SAN Client tape storage destinations
        1.  
          SAN Client tape storage limitations
    5.  
      How to choose SAN Client and Fibre Transport hosts
    6.  
      About NetBackup SAN Client support for agents
    7.  
      About NetBackup SAN Client support for clustering
    8.  
      About NetBackup SAN Client support for Windows Hyper-V Server
    9.  
      About NetBackup SAN Client unsupported restores
    10.  
      About Fibre Transport throughput
    11.  
      Converting a SAN media server to a SAN client
  3. Preparing the SAN
    1.  
      Preparing the SAN
    2.  
      About zoning the SAN for Fibre Transport
    3.  
      About HBAs for SAN clients and Fibre Transport media servers
    4.  
      When selecting the HBA ports for SAN Client
    5.  
      About supported SAN configurations for SAN Client
  4. Licensing SAN Client and Fibre Transport
    1.  
      About SAN Client installation
    2.  
      About the SAN Client license key
    3.  
      When upgrading SAN Client and Fibre Transport
  5. Configuring SAN Client and Fibre Transport
    1.  
      Configuring SAN Client and Fibre Transport
    2. Configuring a Fibre Transport media server
      1.  
        About the target mode driver
      2.  
        About nbhba mode and the ql2300_stub driver
      3.  
        About FC attached devices
      4.  
        How to identify the HBA ports
      5.  
        About HBA port detection on Solaris
      6.  
        About Fibre Transport media servers and VLANs
      7.  
        Starting nbhba mode
      8.  
        Marking the Fibre Transport media server HBA ports
      9.  
        Configuring the media server Fibre Transport services
    3. Configuring SAN clients
      1.  
        About configuring firewalls for SAN clients
      2.  
        SAN client driver requirements
      3.  
        Configuring the SAN client Fibre Transport service
    4. Configuring SAN clients in a cluster
      1.  
        Registering a SAN client cluster virtual name
      2.  
        Setting NetBackup configuration options by using the command line
    5.  
      About configuring Fibre Transport properties
    6.  
      Configuring Fibre Transport properties
    7. Fibre Transport properties
      1.  
        About Linux concurrent FT connections
    8.  
      About SAN client usage preferences
    9. Configuring SAN client usage preferences
      1.  
        SAN client usage preferences
  6. Managing SAN clients and Fibre Transport
    1.  
      Enabling or disabling the Fibre Transport services
    2.  
      Rescanning for Fibre Transport devices from a SAN client
    3.  
      Viewing SAN Client Fibre Transport job details
    4.  
      Viewing Fibre Transport traffic
    5.  
      Adding a SAN client
    6.  
      Deleting a SAN client
  7. Disabling SAN Client and Fibre Transport
    1.  
      About disabling SAN Client and Fibre Transport
    2.  
      Disabling a SAN client
    3.  
      Disabling a Fibre Transport media server
  8. Troubleshooting SAN Client and Fibre Transport
    1.  
      About troubleshooting SAN Client and Fibre Transport
    2.  
      SAN Client troubleshooting tech note
    3.  
      Viewing Fibre Transport logs
    4. About unified logging
      1.  
        About using the vxlogview command to view unified logs
      2.  
        Examples of using vxlogview to view unified logs
    5.  
      Stopping and starting Fibre Transport services
    6.  
      Backups failover to LAN even though Fibre Transport devices available
    7.  
      Kernel warning messages when Veritas modules load
    8.  
      SAN client service does not start
    9.  
      SAN client Fibre Transport service validation
    10.  
      SAN client does not select Fibre Transport
    11.  
      Media server Fibre Transport device is offline
    12.  
      No Fibre Transport devices discovered

Backups failover to LAN even though Fibre Transport devices available

If a NetBackup FT media server has multiple network interfaces for VLANs, backups may failover to LAN transport if the NetBackup host name order is configured incorrectly.

See About Fibre Transport media servers and VLANs.

For all of the hosts that participate in the backups, examine their Additional Servers lists on their NetBackup Administration Console host properties Servers pages. Verify that the FT server's primary host name appears before any other interface names for that FT media server host in. If it does not, fix the incorrect host name order as described in the following table.

Table: How to fix an incorrect host name order in NetBackup

Task

Procedure

Stop the FT services on the media server

See Enabling or disabling the Fibre Transport services.

Delete the FT server from the NetBackup EMM database

Use the following NetBackup command to delete the host from the NetBackup EMM database as an FT media server:

nbftconfig -deleteserver -Me hostname

The host remains in the EMM database as a NetBackup media server.

Re-order the Additional Servers list on each host

If necessary, delete all of the network interface names of the FT media server from the Additional Servers list. Then, add the primary host name first and then the remainder of the host names in any order. The Additional Servers list appears in the host properties Servers page for that host.

See the NetBackup Administrator's Guide, Volume I:

http://www.veritas.com/docs/DOC5332

Start the FT services on the media server

See Enabling or disabling the Fibre Transport services.

Scan for FT devices from each SAN client

When the FT media server is discovered during the rescan operation, NetBackup adds it to the EMM database as an FT media server.

See Rescanning for Fibre Transport devices from a SAN client.