Veritas NetBackup™ 8.0 Troubleshooting Guide
- Introduction
- Troubleshooting procedures
- Troubleshooting NetBackup problems
- Verifying host name and service entries in NetBackup
- Frozen media troubleshooting considerations
- Troubleshooting problems with the NetBackup web services
- Resolving PBX problems
- About troubleshooting Auto Image Replication
- Using NetBackup utilities
- About the NetBackup support utility (nbsu)
- About the NetBackup consistency check utility (NBCC)
- About the robotic test utilities
- Disaster recovery
- About disk recovery procedures for UNIX and Linux
- About clustered NetBackup server recovery for UNIX and Linux
- About disk recovery procedures for Windows
- About clustered NetBackup server recovery for Windows
- About recovering the NetBackup catalog
- About NetBackup catalog recovery and OpsCenter
- About recovering the entire NetBackup catalog
- About recovering the NetBackup catalog image files
- About recovering the NetBackup relational database
Recovering a NetBackup user-directed online catalog backup from the command line
This procedure recovers the catalog manually through the command line interface (CLI) without a Phase 1 import when the disaster recovery (DR) file is available. You must have root (administrative) privileges to perform this procedure.
Note:
Use this procedure only if you want to restore the minimal NetBackup catalog information that lets you begin to recover critical data.
To recover the user-directed online catalog from the command line interface
- Verify the location of the disaster recovery files that are created from Full and Incremental Hot Catalog backups. These files can be stored in a specified path of the file system on the master server and in email attachments to the NetBackup administrator.
- Set up each master server and media server in the same configuration as the configuration that is used during the last catalog backup. The master server and media servers have the following same properties as the backed up catalog configuration: name, NetBackup version, operating system patch level, and path to storage devices.
Configure any devices and volumes you may need for the recovery.
- Locate the latest DR image file corresponding to the backups that are used for recovery. Open the file in an editor and find values for the following:
master_server
Use the exact name that is specified in NetBackup configuration for the master server .
media_server
The location of the robot or disk storage unit that is used for catalog backup.
timestamp
The four most significant digits in the DR file name and six zeroes attached.
media
The location of the catalog backup media as specified by the disaster recovery file under the FRAGMENT keyword.
backup_id
Found in the DR file under BACKUP_ID.
Example:
file: Hot_Backup_1122502016_INCR
timestamp: 1122000000
- Create the DR recovery directory on the master server.
UNIX and Linux:
/usr/openv/netbackup/db/images/master_server/timestamp/tmp
Windows:
C:\Program Files\VERITAS\NetBackup\db\images\master_server \timestamp\tmp
Copy the DR file to the newly created directory.
Edit the DR file in netbackup/db/images/master_server/timestamp/tmp as follows:
Change the value of IMAGE_TYPE to 1.
Change the value of TIR_INFO to 0.
Change the value of NUM_DR_MEDIAS to 0.
Remove ALL lines containing DR_MEDIA_REC.
- If your catalog recover media is on tape, run the vmquery command to assign the media to the media server.
vmquery -assigntohost media timestamp master_server
Example:
vmquery -assigntohost DL005L 1122000000 klingon
- To recover the catalog .f file from the hot catalog backup, run a Phase II import on the media that is specified by the disaster recovery file .
bpimport -server master_server -backupid backup_id
If your catalog backup was incremental, recover all the other catalog backup images up to and including the most recent Full Catalog backup.
Open the Backup, Archive, and Restore client interface for NetBackup. Select NBU-Catalog as the policy type. Set the source clients and destination clients to your master server.
Search the backups and restore all files that are located in the following directory:
install_path/netbackup/db/images/master_server
Verify that all files are restored successfully on the master server.
Restore your critical data by using the Backup, Archive, and Restore client interface or the command line.
Restore the catalog backup images for each media server which requires data recovery.
To restore the backup images, select NBU-Catalog as the policy type. Source and destination clients should be your master server. Refresh your view in the BAR GUI. Traverse the file system for the master server to the following:
install_path/netbackup/db/images
Restore the images for each configured media server. Verify that your images are present by searching for them in the catalog.
- Recover backup data from each media server in the previous step. Change the Policy Type, Source, and Destination client to match the client that is used to back up the desired data. Select the desired files from the Backup, Archive, and Restore client interface and restore them.
- To recover the NetBackup relational database, run the following:
bprecover -r -nbdb
This command restores NetBackup media usage information, ensure that media containing backups are not overwritten, and restore the storage unit configuration.
You cannot recover the NetBackup relational database to a configuration that is not identical to the configuration on which the catalog was backed up. Instead, you must import each piece of backup media.
- If your catalog recovery media is on tape, freeze the media that contains the catalog backup that is used for recovery. This action protects the media from being reused:
bpmedia -freeze -m media -h master_server
Run bpmedialist to verify that the media is frozen.
- Recover your policies and configuration data on each master server and media server.
Before recovering NetBackup policy files, ensure that you have recovered all of your critical data, or protected the media that contains your critical data. When policy information is recovered, NetBackup starts to run the scheduled jobs that may overwrite the media that was written after the last catalog backup.
Open the Backup, Archive, and Restore client interface for NetBackup and select NBU-Catalog as the policy type.
For each server to be restored, set the source clients and destination clients to your server, starting with the master server.
Restore all files that are backed up by the hot catalog backup on each server.
- Stop and restart the NetBackup services.
More Information