Veritas NetBackup™ Device Configuration Guide

Last Published:
Product(s): NetBackup (8.1.1, 8.1)
  1. Introducing device configuration
    1.  
      Using this guide
    2. General device configuration sequence
      1.  
        Configuration cautions
    3.  
      About the NetBackup compatibility lists
  2. Section I. Operating systems
    1. AIX
      1.  
        Before you begin configuring NetBackup on AIX
      2.  
        RS/6000 AIX adapter number conventions
      3.  
        About AIX persistent naming support
      4.  
        About configuring robotic control device files in AIX
      5.  
        About device files for SAN Clients on AIX
      6. About configuring tape drive device files in AIX
        1.  
          About choosing a tape driver on AIX
        2.  
          About non-QIC tape drives on AIX
        3.  
          About extended-file marks for drives
        4.  
          About fast-tape positioning (locate-block) on AIX
        5.  
          About no rewind device files on AIX
        6. Creating AIX no rewind device files for tape drives
          1.  
            Example of creating a no rewind device file
        7.  
          Using multiple tape densities on AIX
        8.  
          About SPC-2 SCSI reserve on AIX
        9.  
          Disabling SPC-2 SCSI reserve in AIX
      7.  
        About Sony AIT drives on AIX
      8.  
        AIX command summary
    2. HP-UX
      1.  
        Before you begin configuring NetBackup on HP-UX
      2.  
        About robotic control on HP-UX
      3.  
        About HP-UX device addressing schemes
      4.  
        HP-UX tape drive device file requirements for NetBackup
      5. About device drivers and files for HP-UX persistent DSFs
        1.  
          About device drivers for persistent DSFs
        2.  
          About persistent DSFs for robotic control
        3.  
          About persistent DSFs for tape drive access
        4.  
          About persistent DSF pass-through paths
      6. About configuring persistent DSFs
        1.  
          Creating HP-UX persistent DSFs
        2.  
          Upgrading NetBackup to use HP-UX persistent DSFs
        3.  
          Creating persistent DSF pass-through paths
      7. About HP-UX legacy device drivers and files
        1.  
          About HP-UX device drivers for legacy device files
        2.  
          About legacy robotic control device files
        3.  
          About legacy tape drive device files
        4.  
          About legacy pass-through paths for tape drives
      8.  
        Creating device files for SAN Clients on HP-UX
      9. About configuring legacy device files
        1. Creating legacy SCSI and FCP robotic controls on HP-UX
          1.  
            Example of how to create a sctl device file for SCSI (PA-RISC)
          2.  
            Example of how to create a sctl device file for FCP (PA-RISC)
          3.  
            Example of how to create sctl device files for FCP (Itanium)
        2.  
          About creating legacy tape drive device files
        3.  
          Creating tape drive pass-through device files
      10.  
        About SPC-2 SCSI reserve on HP-UX
      11.  
        Disabling SPC-2 SCSI reserve in HP-UX
      12.  
        About disabling the HP-UX EMS Tape Device Monitor for a SAN
      13.  
        HP-UX command summary
    3. Linux
      1.  
        Before you begin on Linux
      2. About the required Linux SCSI drivers
        1.  
          About the st driver debug mode
      3.  
        Verifying the Linux drivers
      4. About configuring robot and drive control for Linux
        1.  
          About the Linux robotic control device files
        2.  
          About the Linux tape drive device files
      5.  
        Verifying the device configuration on Linux
      6.  
        About SAN clients on Linux
      7.  
        About SCSI persistent bindings for Linux
      8.  
        About Emulex HBAs
      9.  
        Utilities to test SCSI devices
      10.  
        Linux command summary
    4. Solaris
      1.  
        Before you begin on Solaris
      2.  
        About the NetBackup sg driver
      3.  
        Determining if the NetBackup sg driver is installed
      4.  
        Special configuration for the Oracle StorEdge Network Foundation HBA driver
      5.  
        About binding Fibre Channel HBA drivers
      6.  
        Configuring Solaris 10 x86 for multiple drive paths
      7. Installing/reinstalling the sg and the st drivers
        1.  
          st.conf file example
        2.  
          sg.conf file example
        3.  
          sg.links file example
      8.  
        Configuring 6 GB and larger SAS HBAs in Solaris
      9.  
        Preventing Solaris driver unloading
      10. About Solaris robotic controls
        1.  
          About SCSI and FCP robotic controls on Solaris
        2.  
          Examples of SCSI and FCP robotic control device files on Solaris
      11. About Solaris tape drive device files
        1.  
          About Berkeley-style close
        2.  
          About no rewind device files on Solaris
        3.  
          About fast-tape positioning (locate-block) on Solaris
        4.  
          About SPC-2 SCSI reserve on Solaris
        5.  
          Disabling SPC-2 SCSI reserve on Solaris
        6.  
          About nonstandard tape drives
      12. Configuring Solaris SAN clients to recognize FT media servers
        1.  
          Adding the FT device entry to the st.conf file
        2.  
          Modifying the st.conf file so that Solaris discovers devices on two LUNS
      13.  
        Uninstalling the sg driver on Solaris
      14.  
        Solaris command summary
    5. Windows
      1.  
        Before you begin configuring NetBackup on Windows
      2.  
        About tape device drivers on Windows
      3.  
        Attaching devices to a Windows system
  3. Section II. Robotic storage devices
    1. Robot overview
      1.  
        NetBackup robot types
      2. NetBackup robot attributes
        1.  
          ACS robots
        2.  
          TLD robots
      3.  
        Table-driven robotics
      4.  
        Robotic test utilities
      5. Robotic processes
        1.  
          Processes by robot type
        2.  
          Robotic process example
    2. Oracle StorageTek ACSLS robots
      1.  
        About Oracle StorageTek ACSLS robots
      2.  
        Sample ACSLS configurations
      3.  
        Media requests for an ACS robot
      4.  
        About configuring ACS drives
      5.  
        Configuring shared ACS drives
      6.  
        Adding tapes to ACS robots
      7. About removing tapes from ACS robots
        1.  
          Removing tapes using the ACSLS utility
        2.  
          Removing tapes using NetBackup
      8. Robot inventory operations on ACS robots
        1.  
          Configuring a robot inventory filtering on ACS robots
      9. NetBackup robotic control, communication, and logging
        1.  
          NetBackup robotic control, communication, and logging for Windows systems
        2. NetBackup robotic control, communication, and logging for UNIX systems
          1.  
            NetBackup ACS daemon (acsd)
          2.  
            NetBackup ACS SSI event logger (acssel)
          3.  
            Using acssel with a different socket name
          4.  
            NetBackup ACS storage server interface (acsssi)
          5.  
            About the ACS_SSI_SOCKET configuration option
          6.  
            Starting acsssi manually
          7.  
            Optional environment variables
      10. ACS robotic test utility
        1.  
          acstest on Windows systems
        2.  
          acstest on UNIX systems
      11.  
        Changing your ACS robotic configuration
      12. ACS configurations supported
        1.  
          Multiple ACS robots with one ACS library software host
        2.  
          Multiple ACS robots and ACS library software hosts
      13.  
        Oracle StorageTek ACSLS firewall configuration
    3. Device configuration examples
      1.  
        An ACS robot on a Windows server example
      2.  
        An ACS robot on a UNIX server example

Robot inventory operations on ACS robots

If the ACS library software host is a Sun StorageTek Library Station, an Inventory Robot Filter (INVENTORY_FILTER) entry may be required in the vm.conf file. Old versions of Library Station do not support queries of all volumes in an ACS robot.

In NetBackup, the ACS robot type supports bar codes.

The following sequence of events occurs when you inventory an ACS robot in NetBackup:

  • NetBackup requests volume information from the ACS library software.

  • The ACS library software provides a listing of the volume IDs, media types, ACS location, and LSM location from its database.

    See Table: ACS drive coordinates.

  • NetBackup maps the volume IDs into media IDs and bar codes. For example in the previous table, volume ID 100011 becomes media ID 100011 and the barcode for that media ID is also 100011.

  • If the operation does not require a volume configuration update, NetBackup uses the media type defaults for ACS robots when it creates its report.

  • If the operation requires a volume configuration update, NetBackup does the following:

    • Maps the ACS media types to the default NetBackup media types.

    • Adds the ACS and the LSM locations for new volumes to the EMM database. This location information is used for media and drive selection.

Information about the default media type mappings and how to configure media type mappings is available.

See the NetBackup Administrator's Guide, Volume I.

The following table shows an example of the ACS drive coordinates that NetBackup receives.

Table: ACS drive coordinates

ACS volume ID

ACS media type

ACS

LSM

100011

DLTIV

0

0

200201

DD3A

0

0

412840

STK1R

0

1

412999

STK1U

0

1

521212

JLABEL

0

0

521433

STK2P

0

1

521455

STK2W

0

1

770000

LTO_100G

0

0

775500

SDLT

0

0

900100

EECART

0

0

900200

UNKNOWN

0

0