Veritas NetBackup™ Device Configuration Guide
- Introducing device configuration
- Section I. Operating systems
- AIX
- Before you begin configuring NetBackup on AIX
- RS/6000 AIX adapter number conventions
- About AIX persistent naming support
- About configuring robotic control device files in AIX
- About device files for SAN Clients on AIX
- About configuring tape drive device files in AIX
- About choosing a tape driver on AIX
- About non-QIC tape drives on AIX
- About extended-file marks for drives
- About fast-tape positioning (locate-block) on AIX
- About no rewind device files on AIX
- Creating AIX no rewind device files for tape drives
- Using multiple tape densities on AIX
- About SPC-2 SCSI reserve on AIX
- Disabling SPC-2 SCSI reserve in AIX
- About Sony AIT drives on AIX
- AIX command summary
- HP-UX
- Before you begin configuring NetBackup on HP-UX
- About robotic control on HP-UX
- About HP-UX device addressing schemes
- HP-UX tape drive device file requirements for NetBackup
- About device drivers and files for HP-UX persistent DSFs
- About configuring persistent DSFs
- About HP-UX legacy device drivers and files
- Creating device files for SAN Clients on HP-UX
- About configuring legacy device files
- About SPC-2 SCSI reserve on HP-UX
- Disabling SPC-2 SCSI reserve in HP-UX
- About disabling the HP-UX EMS Tape Device Monitor for a SAN
- HP-UX command summary
- Linux
- Before you begin on Linux
- About the required Linux SCSI drivers
- Verifying the Linux drivers
- About configuring robot and drive control for Linux
- Verifying the device configuration on Linux
- About SAN clients on Linux
- About SCSI persistent bindings for Linux
- About Emulex HBAs
- Utilities to test SCSI devices
- Linux command summary
- Solaris
- Before you begin on Solaris
- About the NetBackup sg driver
- Determining if the NetBackup sg driver is installed
- Special configuration for the Oracle StorEdge Network Foundation HBA driver
- About binding Fibre Channel HBA drivers
- Configuring Solaris 10 x86 for multiple drive paths
- Installing/reinstalling the sg and the st drivers
- Configuring 6 GB and larger SAS HBAs in Solaris
- Preventing Solaris driver unloading
- About Solaris robotic controls
- About Solaris tape drive device files
- Configuring Solaris SAN clients to recognize FT media servers
- Uninstalling the sg driver on Solaris
- Solaris command summary
- Windows
- AIX
- Section II. Robotic storage devices
- Robot overview
- Oracle StorageTek ACSLS robots
- About Oracle StorageTek ACSLS robots
- Sample ACSLS configurations
- Media requests for an ACS robot
- About configuring ACS drives
- Configuring shared ACS drives
- Adding tapes to ACS robots
- About removing tapes from ACS robots
- Robot inventory operations on ACS robots
- NetBackup robotic control, communication, and logging
- ACS robotic test utility
- Changing your ACS robotic configuration
- ACS configurations supported
- Oracle StorageTek ACSLS firewall configuration
- Device configuration examples
About Sony AIT drives on AIX
Sony S-AIT drives have DIP switches (SWA and SWB) located on the bottom of the drive.
For the NetBackup Shared Storage Option, you must set the SWA-1 (No Reply Unit Attention After Process Login) switch correctly. Its factory setting depends on the serial number of the drive.
If the drive has an early serial number, switch SWA-1 may be OFF. If so, change the switch to ON.
Drives with newer serial numbers have SWA-1 set to ON as the default.
These newer serial numbers are as follows:
SDZ-130 :01442007 and later
SDZ-130/L :01200696 and later
Also, for the drives that have a date of May 17, 2004 and later, the DIP switch is set to ON.
The following table shows the dip switch settings for the newer serial number drives.
Table: DIP switch positions for AIT drives
Switch | Setting (1 = ON and 0 = OFF) |
|---|---|
SWA-1 | 1 |
SWA-2 | 0 |
SWA-3 | 0 |
SWA-4 | 0 |
SWA-5 | 0 |
SWA-6 | 0 |
SWA-7 | 1 |
SWA-8 | 0 |