Veritas NetBackup™ Appliance コマンドリファレンスガイド

Last Published:
Product(s): Appliances (3.1.1 (5340), 3.1.1 (5330), 3.1.1 (5240), 3.1.1 (5230), 3.1.1 (5220))
  1. 概要
    1.  
      NetBackup Appliance Shell Menuについて
    2. NetBackup Appliance Shell Menuへのログオン
      1.  
        構成されていないアプライアンスに対するコマンドの制限
    3.  
      NetBackup Appliance Shell Menuの使用
    4. NetBackup Appliance Shell Menuコマンドビューについて
      1.  
        ［アプライアンス (Appliance)］ビューのコマンドについて
      2.  
        ［管理 (Manage)］ビューのコマンドについて
      3.  
        ［監視 (Monitor)］ビューのコマンドについて
      4.  
        ［ネットワーク (Network)］ビューのコマンドについて
      5.  
        ［レポート (Reports)］ビューのコマンドについて
      6.  
        ［設定 (Settings)］ビューのコマンドについて
      7.  
        ［サポート (Support)］ビューのコマンドについて
  2. 付録 A. Main > Appliance コマンド
    1.  
      Appliance > Master
    2.  
      Appliance > Media
    3.  
      Appliance > Management
    4.  
      Appliance > Remove
    5.  
      Appliance > ShowDedupPassword
    6.  
      アプライアンス > ShowIdentity
    7.  
      Appliance > Status
  3. 付録 B. Main > Manage > FibreChannel コマンド
    1.  
      Manage > FibreChannel > Clean
    2.  
      Manage > FibreChannel > Configure
    3.  
      Manage > FibreChannel > Reset
    4.  
      Manage > FibreChannel > Scan
    5.  
      Manage > FibreChannel > Show
    6.  
      Manage > FibreChannel > Statistics
  4. 付録 C. Main > Manage > HighAvailability コマンド
    1.  
      Manage > HighAvailability > AddNode
    2.  
      Manage > HighAvailability > GetAssetTag
    3.  
      Manage > HighAvailability > RemoveNode
    4.  
      Manage > HighAvailability > Setup
    5.  
      Manage > HighAvailability > Status
    6.  
      Manage > HighAvailability > Switchover
  5. 付録 D. Main > Manage > Libraries コマンド
    1.  
      Manage > Libraries > Configure
    2.  
      Manage > Libraries > Deny
    3.  
      Manage > Libraries > Down
    4.  
      Manage > Libraries > Inventory
    5.  
      Manage > Libraries > List
    6.  
      Manage > Libraries > Requests
    7.  
      Manage > Libraries > Reset
    8.  
      Manage > Libraries > Resubmit
    9.  
      Manage > Libraries > Up
  6. 付録 E. Main > Manage > Libraries > Advanced > ACS コマンド
    1.  
      Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
    2.  
      Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
    3.  
      Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
    4.  
      Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
    5.  
      Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
    6.  
      Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
    7.  
      Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
    8.  
      Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
    9.  
      Manage > Libraries > Advanced > ACS > TestACS
    10.  
      Manage > Libraries > Advanced > ACS > ViewVMconf
  7. 付録 F. Main > Manage > License コマンド
    1.  
      Manage > License > Add
    2.  
      Manage > License > List
    3.  
      Manage > License > ListInfo
    4.  
      Manage > License > Remove
  8. 付録 G. Main > Manage > MountPoints コマンド
    1.  
      Manage > MountPoints > List
    2.  
      Manage > MountPoints > Mount
    3.  
      Manage > MountPoints > Unmount
  9. 付録 H. Main > Manage > NetBackup CLI コマンド
    1.  
      Manage > NetBackupCLI > Create
    2.  
      Manage > NetBackupCLI > Delete
    3.  
      Manage > NetBackupCLI > List
    4.  
      Manage > NetBackupCLI > PasswordExpiry
  10. 付録 I. Main > Manage > OpenStorage コマンド
    1.  
      Manage > OpenStorage > Install
    2.  
      Manage > OpenStorage > List
    3.  
      Manage > OpenStorage > Readme
    4.  
      Manage > OpenStorage > Share
    5.  
      Manage > OpenStorage > Uninstall
  11. 付録 J. Main > Manage > Software コマンド
    1.  
      Manage > Software > Cancel
    2.  
      Manage > Software > Delete
    3.  
      Manage > Software > Download
    4.  
      Manage > Software > DownloadProgress
    5.  
      Manage > Software > Firmware
    6.  
      Manage > Software > Install
    7.  
      Manage > Software > List
    8.  
      Manage > Software > LiveUpdateClients
    9.  
      Manage > Software > Readme
    10.  
      Manage > Software > Rollback
    11.  
      Manage > Software > Share
    12.  
      Manage > Software > UpgradeStatus
  12. 付録 K. Main > Manage > Storage コマンド
    1.  
      Manage > Storage > Add
    2.  
      Manage > Storage > Create
    3.  
      Manage > Storage > Delete
    4.  
      Manage > Storage > Edit
    5.  
      Manage > Storage > Monitor
    6.  
      Manage > Storage > Move
    7.  
      Manage > Storage > Remove
    8.  
      Manage > Storage > Resize
    9.  
      Manage > Storage > Scan
    10.  
      Manage > Storage > Show
    11.  
      Manage > Storage > Erase
  13. 付録 L. Main > Manage > Tapes コマンド
    1.  
      Manage > Tapes > Cleaning
    2.  
      Manage > Tapes > Delete
    3.  
      Manage > Tapes > Eject
    4.  
      Manage > Tapes > Freeze
    5.  
      Manage > Tapes > Inventory
    6.  
      Manage > Tapes > List
    7.  
      Manage > Tapes > ListNetBackupMedia
    8.  
      Manage > Tapes > Suspend
    9.  
      Manage > Tapes > Unfreeze
    10.  
      Manage > Tapes > Unsuspend
  14. 付録 M. Main > Manage > Certificates コマンド
    1.  
      Manage > Certificates > Generate
    2.  
      Manage > Certificates > Delete
  15. 付録 N. Main > Monitor コマンド
    1.  
      Monitor > Beacon
    2.  
      Monitor > MemoryStatus
    3.  
      Monitor > NetBackup
    4.  
      Monitor > NetworkStatus
    5.  
      ［監視 (Monitor)］>［SDCS］
    6.  
      Monitor > Top
    7.  
      Monitor > Uptime
    8.  
      Monitor > Who
    9.  
      Monitor > Hardware
  16. 付録 O. Main > Network コマンド
    1.  
      Network > Configure
    2.  
      Network > Date
    3.  
      Network > DNS
    4.  
      Network > Gateway
    5.  
      Network > Hostname
    6.  
      Network > Hosts
    7.  
      Network > IPv4
    8.  
      Network > IPv6
    9.  
      Network > LinkAggregation
    10.  
      Network > NetStat
    11.  
      Network > NTPServer
    12.  
      Network > Ping
    13.  
      Network > SetProperty
    14.  
      Network > Show
    15.  
      Network > TimeZone
    16.  
      Network > TraceRoute
    17.  
      Network > Unconfigure
    18.  
      Network > VLAN
    19.  
      Network > WANOptimization
  17. 付録 P. Main > Network > Security (IPsec) コマンド
    1.  
      Network > IPsec > Configure
    2.  
      Network > IPsec > Delete
    3.  
      Network > IPsec > Export
    4.  
      Network > IPsec > Import
    5.  
      Network > IPsec > Provision
    6.  
      Network > IPsec > Refresh
    7.  
      Network > IPsec > Show
    8.  
      Network > IPsec > Unconfigure
  18. 付録 Q. Main > Reports コマンド
    1.  
      Reports > Deduplication
    2.  
      Reports > Process
  19. 付録 R. Main > Settings コマンド
    1.  
      Settings > Cloud
    2.  
      Settings > Deduplication
    3.  
      Settings > FibreTransport
    4.  
      Settings > iSCSI > Initiator
    5.  
      Settings > iSCSI > Interface
    6.  
      Settings > iSCSI > Target
    7.  
      Settings > LogForwarding
    8.  
      Settings > LifeCycle
    9.  
      Settings > LiveUpdateServer
    10.  
      Settings > NetBackup
    11.  
      ［設定 (Settings)］>［パスワード (Password)］
    12.  
      Settings > Share
    13.  
      Settings > SNMP polling
    14.  
      Settings > Sysctl
    15.  
      Settings > SystemLocale
  20. 付録 S. Main > Settings > Alerts コマンド
    1.  
      Settings > Alerts > CallHome
    2.  
      Settings > Alerts > Email
    3.  
      Settings > Alerts > Hardware
    4.  
      Settings > Alerts > SNMP
  21. 付録 T. Main > Settings > Notifications view コマンド
    1.  
      Settings > Notifications > LoginBanner
  22. 付録 U. Main > Settings > Security コマンド
    1.  
      Settings > Security > Authorization
    2.  
      Settings > Security > Authentication > ActiveDirectory
    3.  
      Settings > Security > Authentication > Kerberos
    4.  
      Settings > Security > Authentication > LDAP
    5.  
      Settings > Security > Authentication > LocalUser
    6.  
      Main > Settings > Security > STIG
    7.  
      Main > Settings > Security > FIPS
  23. 付録 V. Main > Support コマンド
    1.  
      Support > Checkpoint
    2.  
      Support > Cleanup > RemoveShelfEntries
    3.  
      Support > Cleanup > ResetDIMMErrors
    4.  
      Support > Collect
    5.  
      Support > DataCollect
    6.  
      Support > Disk
    7.  
      Support > Errors
    8.  
      Support > FactoryReset
    9.  
      Support > FibreTransport
    10.  
      Support > InfraServices
    11.  
      Support > iostat
    12.  
      Support > IPMI
    13.  
      Support > KillRemoteCall
    14.  
      Support > Logs
    15.  
      Support > Maintenance
    16.  
      Support > Messages
    17.  
      Support > NBDNA
    18.  
      Support > nbperfchk
    19.  
      Support > NBSU
    20.  
      Support > Processes
    21.  
      Support > RAID
    22.  
      Support > Reboot
    23.  
      Support > RecoverStorage
    24.  
      Support > Service
    25.  
      Support > ServiceAllowed
    26.  
      Support > Show
    27.  
      Support > Shutdown
    28.  
      Support > Storage ClearReservations
    29.  
      Support > Storage Reset
    30.  
      Support > Storage SanityCheck
    31.  
      Support > Test

名前

Main > Settings > Sysctl — sysctl パラメータ値を設定、表示、および一覧表示します。

概要

ApplianceDefault

List

Show

Tune

説明

このコマンドで sysctl パラメータ値を修正できます。Sysctl は実行時、カーネルパラメータの修正に使用されます。

オプション

ApplianceDefault Parameter

パラメータをアプライアンスのインストールのデフォルト値に設定します。ここでは、Parameter は sysctl パラメータの名前です。

List

修正可能な sysctl パラメータを一覧表示します。

Show Parameter

sysctl パラメータ値を表示します。ここでは、Parameter は sysctl パラメータの名前です。

Tune Parameter Value

sysctl パラメータ値を設定します。ここでは、Parameter は sysctl パラメータの名前で、Value はパラメータ値です。

例

次に、Settings > Sysctl コマンドを実行したときに表示される情報の例を示します。

abc123.Sysctl> List
net.ipv4.tcp_keepalive_time
vm.zone_reclaim_mode
vm.min_free_kbytes