NetBackup™ Web UI RHV Administrator's Guide

Last Published:
Product(s): NetBackup (9.0.0.1, 9.0)
  1. Introducing the NetBackup web user interface
    1.  
      About the NetBackup web UI
    2.  
      Terminology
    3.  
      Sign in to the NetBackup web UI
    4.  
      Sign out of the NetBackup web UI
  2. Monitoring and notifications
    1.  
      The NetBackup dashboard
    2.  
    3.  
  3. Managing RHV servers
    1.  
      Quick configuration checklist to protect Red Hat Virtualization virtual machines
    2. Configuring secure communication between the Red Hat Virtualization server and NetBackup host
      1.  
        ECA_TRUST_STORE_PATH for NetBackup servers and clients
      2.  
        ECA_CRL_PATH for NetBackup servers and clients
      3.  
        VIRTUALIZATION_HOSTS_SECURE_CONNECT_ENABLED for servers and clients
      4.  
        VIRTUALIZATION_CRL_CHECK for NetBackup servers and clients
    3.  
      About the ports that NetBackup uses to communicate with RHV
    4. Add or browse an RHV manager
      1.  
        Adding a backup host to the NetBackup master server
      2.  
        Remove an RHV manager
    5.  
      Create an intelligent VM group
    6.  
      Remove an intelligent VM group
    7.  
      Setting global limits on the use of RHV resources
  4. Protecting RHV virtual machines
    1.  
      Things to know before you protect RHV virtual machines
    2.  
      Protect RHV VMs or intelligent VM groups
    3. Edit protection settings for a RHV asset
      1.  
        Schedules and retention
      2.  
        Backup options
    4.  
      Remove protection from VMs or intelligent VM groups
    5.  
      View the protection status of VMs or intelligent VM groups
  5. Recovering RHV virtual machines
    1.  
      Things to consider before you recover the RHV virtual machines
    2.  
      About the pre-recovery check
    3.  
      Recover an RHV virtual machine
    4.  
      About the supported virtual disk formats and disk provisioning during VM recovery
  6. Troubleshooting RHV VM protection and recovery
    1.  
      Troubleshooting tips for NetBackup for RHV
    2.  
      Error during the RHV virtual machines discovery phase
    3.  
      Error run into while backing up RHV virtual machines
    4.  
      Error while restoring RHV virtual machines
  7. API and command line options for RHV
    1. Using APIs and command line options to manage, protect, or recover RHV virtual machines
      1.  
        Additional information about the rename file
    2. Additional NetBackup options for RHV configuration
      1.  
        OVIRT_IMAGEIO_INACTIVITY_TIMEOUT option for NetBackup servers
      2.  
        RHV_CREATEDISK_TIMEOUT option for NetBackup servers
      3.  
        RHV_AUTODISCOVERY_INTERVAL option for NetBackup servers

Error run into while backing up RHV virtual machines

The following table describes the problem that might occur when you back up RHV virtual machines:

Table: Error while backing up RHV virtual machines

Error message or cause

Explanation and recommended action

After a NetBackup backup operation, the VM snapshot on the RHV manager is not deleted.

If a disk attached to the VM is in an inactive state, then the RHV manager does not delete the VM snapshot after a backup operation is complete.

Workaround:

  • Before the backup operation, verify the state of the disks that are attached to the VM and ensure that they are active.

  • Ensure that the disks are not attached while the VM is running, thus preventing the disk to be in an inactive state.

VM backup fails with the following error:

"The virtual machine has no disks or contains only Raw Device Mappings for disks: Status 25"

This temporary error might occur when the VM snapshot is not available for the backup operation. The backup job is successful on the second attempt.

Unable to remove the older snapshots from the RHV manager when the disk is in a locked state.

The following error is displayed:

A NetBackup snapshot of the virtual machine exist.

Workaround:

Accelerator option does not work.

When a backup policy is created using APIs and the use Accelerator option is enabled, the policy gets created but the NetBackup Accelerator feature does not work.

NetBackup Accelerator is not supported for RHV.