Veritas NetBackup™ for SAP Administrator's Guide
- Introduction to NetBackup for SAP
- Introduction to NetBackup SAP HANA
- Installing NetBackup for SAP
- Installing NetBackup for SAP HANA
- Configuring NetBackup for SAP
- About configuring a backup policy for an SAP database
- About adding schedules to a NetBackup for SAP policy
- NetBackup for SAP backup scripts
- About SAP configuration files
- Configuring NetBackup for SAP HANA
- Configuring the master server for NetBackup SAP HANA
- Configuring the NetBackup client
- Configuring the SAP HANA Agent
- Performing backups and restores of SAP
- Using BRTools to start an SAP backup (for Oracle database only)
- Performing an SAP archive
- Restarting failed NetBackup for SAP backups and restores
- Restarting NetBackup for SAP backups
- Restarting SAP database restores on Oracle
- Performing backups and restores of SAP HANA
- NetBackup for SAP with Snapshot Client
- How the NetBackup for SAP Snapshot Client works
- About configuring Snapshot Client with NetBackup for SAP
- About configuring NetBackup for SAP block-level incremental backups on UNIX
- Configuring policies for BLI backups with NetBackup for SAP
- About NetBackup for SAP restores of volumes and file systems using snapshot rollback
- NetBackup for SAP on MaxDB databases
- Using NetBackup for SAP on a MaxDB database to perform backups and restores
- Troubleshooting NetBackup for SAP and SAP HANA
- NetBackup debug logs and reports
- sapdba logs and messages (Oracle-based SAP environments only)
- About troubleshooting NetBackup for SAP HANA
- Appendix A. backint command line interface
- Appendix B. Input and output files for SAP HANA
- Appendix C. backint -i in_file contents
- Appendix D. backint -o out_file contents
- Appendix E. NetBackup for SAP environment variables for backint
- Appendix F. NetBackup for SAP configuration or bp.conf file settings
- Appendix G. Parameters used in initSID.utl
- sort_backup_type <value>
- sort_restore_type <value>
- Appendix H. Configuring split mirror backups
- Appendix I. Register authorized locations
Registering authorized locations used by a NetBackup database script-based policy
During a backup, NetBackup checks for scripts in the default script location and any authorized locations. The default, authorized script location for UNIX is
usr/openv/netbackup/ext/db_ext and for Windows is
install_path\netbackup\dbext. If the script is not in the default script location or an authorized location, the policy job fails. You can move any script into the default script location or any additional authorized location and NetBackup recognizes the scripts. You need to update the policy with the script location if it has changed. An authorized location can be a directory and NetBackup recognizes any script within that directory. An authorized location can also be a full path to a script if an entire directory does need to be authorized.
If the default script location does not work for your environment, use the following procedure to enter one or more authorized locations for your scripts. Use nbsetconfig to enter an authorized location where the scripts reside. You can also use bpsetconfig, however this command is only available on the master or the media server.
One recommendation is that scripts should not be world-writable. NetBackup does not allow scripts to run from network or remote locations. All scripts must be stored and run locally. Any script that is created and saved in the NetBackup
db_ext (UNIX) or
dbext (Windows) location needs to be protected during a NetBackup uninstall.
For more information about registering authorized locations and scripts, review the knowledge base article:
To add an authorized location
- Open a command prompt on the client.
- Use nbsetconfig to enter values for an authorized location. The client privileged user must run these commands.
The following examples are for paths you may configure for the Oracle agent. Use the path that is appropriate for your agent.
[root@client26 bin]# ./nbsetconfig nbsetconfig>DB_SCRIPT_PATH = /Oracle/scripts nbsetconfig>DB_SCRIPT_PATH = /db/Oracle/scripts/full_backup.sh nbsetconfig> <ctrl-D>
C:\Program Files\Veritas\NetBackup\bin>nbsetconfig nbsetconfig> DB_SCRIPT_PATH=c:\db_scripts nbsetconfig> DB_SCRIPT_PATH=e:\oracle\fullbackup\full_rman.sh nbsetconfig> <ctrl-Z>
Review the NetBackup Command Reference Guide for options, such as reading from a text file and remotely setting clients from a NetBackup server using bpsetconfig. If you have a text file with the script location or authorized locations listed, nbsetconfig or bpsetconfig can read from that text file. An entry of DB_SCRIPT_PATH=none does not allow any script to execute on a client. The none entry is useful if an administrator wants to completely lock down a server from executing scripts.
- (Conditional) Perform these steps on any clustered database or agent node that can perform the backup.
- (Conditional) Update any policy if the script location was changed to the default or authorized location.