Veritas NetBackup™ Appliance 命令参考指南

Last Published:
Product(s): Appliances (5.3)
Platform: NetBackup Appliance OS
  1. 概述
    1.  
      关于 NetBackup Appliance 命令行操作界面
    2. 登录到 NetBackup Appliance 命令行操作界面
      1.  
        未配置设备上的命令限制
    3.  
      使用 NetBackup Appliance 命令行操作界面
    4. 关于 NetBackup Appliance 命令行操作界面命令视图
      1.  
        关于 Appliance 视图下的命令
      2.  
        关于 Manage 视图下的命令
      3.  
        关于 Monitor 视图下的命令
      4.  
        关于 Network 视图下的命令
      5.  
        关于 Reports 视图下的命令
      6.  
        关于 Settings 视图下的命令
      7.  
        关于 Support 视图下的命令
  2. 附录 A. Main > Appliance 命令
    1.  
      Appliance > Primary
    2.  
      Appliance > Media
    3.  
      Appliance > Management
    4.  
      Appliance > Remove
    5.  
      Appliance > ShowDedupPassword
    6.  
      Appliance > ShowIdentity
    7.  
      Appliance > Status
  3. 附录 B. Main > Manage > FibreChannel 命令
    1.  
      Manage > FibreChannel > Clean
    2.  
      Manage > FibreChannel > Configure
    3.  
      Manage > FibreChannel > Reset
    4.  
      Manage > FibreChannel > Scan
    5.  
      Manage > FibreChannel > Show
    6.  
      Manage > FibreChannel > Statistics
  4. 附录 C. Main > Manage > HighAvailability 命令
    1.  
      Manage > HighAvailability > AddNode
    2.  
      Manage > HighAvailability > AutoFix
    3.  
      Manage > HighAvailability > GetAssetTag
    4.  
      Manage > HighAvailability > RemoveNode
    5.  
      Manage > HighAvailability > Setup
    6.  
      Manage > HighAvailability > Status
    7.  
      Manage > HighAvailability > Switchover
  5. 附录 D. Main > Manage > Libraries 命令
    1.  
      Manage > Libraries > Configure
    2.  
      Manage > Libraries > Deny
    3.  
      Manage > Libraries > Down
    4.  
      Manage > Libraries > Inventory
    5.  
      Manage > Libraries > List
    6.  
      Manage > Libraries > Requests
    7.  
      Manage > Libraries > Reset
    8.  
      Manage > Libraries > Resubmit
    9.  
      Manage > Libraries > Up
  6. 附录 E. Main > Manage > Libraries > Advanced > ACS 命令
    1.  
      Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
    2.  
      Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
    3.  
      Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
    4.  
      Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
    5.  
      Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
    6.  
      Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
    7.  
      Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
    8.  
      Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
    9.  
      Manage > Libraries > Advanced > ACS > TestACS
    10.  
      Manage > Libraries > Advanced > ACS > ViewVMconf
  7. 附录 F. Main > Manage > License 命令
    1.  
      Manage > License
  8. 附录 G. Main > Manage > MountPoints 命令
    1.  
      Manage > MountPoints > List
    2.  
      Manage > MountPoints > Mount
    3.  
      Manage > MountPoints > Unmount
  9. 附录 H. Main > Manage > NetBackup CLI 命令
    1.  
      Manage > NetBackupCLI > AllowSelfService
    2.  
      Manage > NetBackupCLI > Create
    3.  
      Manage > NetBackupCLI > Delete
    4.  
      Manage > NetBackupCLI > List
  10. 附录 I. Main > Manage > OpenStorage 命令
    1.  
      Manage > OpenStorage > Install
    2.  
      Manage > OpenStorage > List
    3.  
      Manage > OpenStorage > Readme
    4.  
      Manage > OpenStorage > Share
    5.  
      Manage > OpenStorage > Uninstall
  11. 附录 J. Main > Manage > Software 命令
    1.  
      Manage > Software > Cancel
    2.  
      Manage > Software > Delete
    3.  
      Manage > Software > Download
    4.  
      Manage > Software > DownloadAnalyzer
    5.  
      Manage > Software > DownloadProgress
    6.  
      Manage > Software > Firmware
    7.  
      Manage > Software > Install
    8.  
      Manage > Software > List
    9.  
      Manage > Software > Readme
    10.  
      Manage > Software > Rollback
    11.  
      Manage > Software > Share
    12.  
      Manage > Software > UpgradeReadinessCheck
    13.  
      Manage > Software > UpgradeStatus
    14.  
      Manage > Software > VxUpdate
  12. 附录 K. Main > Manage > Storage 命令
    1.  
      Manage > Storage > Add
    2.  
      Manage > Storage > Create
    3.  
      Manage > Storage > Delete
    4.  
      Manage > Storage > Edit
    5.  
      Manage > Storage > Monitor
    6.  
      Manage > Storage > Move
    7.  
      Manage > Storage > Remove
    8.  
      Manage > Storage > Resize
    9.  
      Manage > Storage > Scan
    10.  
      Manage > Storage > Show
  13. 附录 L. Main > Manage > Tapes 命令
    1.  
      Manage > Tapes > Cleaning
    2.  
      Manage > Tapes > Delete
    3.  
      Manage > Tapes > Eject
    4.  
      Manage > Tapes > Freeze
    5.  
      Manage > Tapes > Inventory
    6.  
      Manage > Tapes > List
    7.  
      Manage > Tapes > ListNetBackupMedia
    8.  
      Manage > Tapes > Suspend
    9.  
      Manage > Tapes > Unfreeze
    10.  
      Manage > Tapes > Unsuspend
  14. 附录 M. Main > Monitor 命令
    1.  
      Monitor > Beacon
    2.  
      监视 > 硬件
    3.  
      Monitor > MemoryStatus
    4.  
      Monitor > NetBackup
    5.  
      Monitor > NetworkStatus
    6.  
      Monitor > SDCS
    7.  
      Monitor > Top
    8.  
      Monitor > Uptime
    9.  
      Monitor > Who
  15. 附录 N. Main > Network 命令
    1.  
      Network > Configure
    2.  
      Network > Date
    3.  
      Network > DNS
    4.  
      Network > Gateway
    5.  
      Network > Hostname
    6.  
      Network > Hosts
    7.  
      Network > IPv4
    8.  
      Network > IPv6
    9.  
      Network > LinkAggregation
    10.  
      Network > NetStat
    11.  
      Network > NTPServer
    12.  
      Network > Ping
    13.  
      Network > SetProperty
    14.  
      Network > Show
    15.  
      Network > TimeZone
    16.  
      Network > TraceRoute
    17.  
      Network > Unconfigure
    18.  
      Network > VLAN
    19.  
      Network > WANOptimization
  16. 附录 O. Main > Network > Security 命令 (DeviceCert)
    1.  
      Network > Security > Export
    2.  
      Network > Security > Import
  17. 附录 P. Main > Reports 命令
    1.  
      Reports > Deduplication
    2.  
      Reports > Process
  18. 附录 Q. Main > Settings 命令
    1.  
      Settings > Deduplication
    2.  
      Settings > FibreTransport
    3.  
      Settings > iSCSI > Initiator
    4.  
      Settings > iSCSI > Interface
    5.  
      Settings > iSCSI > Target
    6.  
      Settings > LifeCycle
    7.  
      Settings > LogForwarding
    8.  
      Settings > NetBackup
    9.  
      Settings > NetBackup DNAT
    10.  
      Settings > NetBackup NATServers
    11.  
      设置 > 密码
    12.  
      Settings > Share
    13.  
      Settings > SNMP
    14.  
      Settings > Sysctl
    15.  
      Settings > SystemLocale
  19. 附录 R. Main > Settings > Alerts 命令
    1.  
      Settings > Alerts > CallHome
    2.  
      Settings > Alerts > Email
    3.  
      Settings > Alerts > Hardware
    4.  
      Settings > Alerts > SNMP
    5.  
      Settings > Alerts > Transmission
  20. 附录 S. Main > Settings > Notifications 视图命令
    1.  
      Settings > Notifications > LoginBanner
  21. 附录 T. Main > Settings > Security 命令
    1.  
      Settings > Security > Antimalware
    2.  
      Settings > Security > Authorization
    3.  
      Settings > Security > Authentication > AccountStatus
    4.  
      Settings > Security > Authentication > ActiveDirectory
    5.  
      Main > Settings > Security > Authentication > CIFSShare
    6.  
      Settings > Security > Authentication > LDAP
    7.  
      Settings > Security > Authentication > LocalUser
    8.  
      Settings > Security > Authentication > MFA
    9.  
      Settings > Security > Authentication > SingleSignOn
    10.  
      Settings > Security > Authentication > SmartCard > SSH
    11.  
      Settings > Security > Authentication > SmartCard
    12.  
      Main > Settings > Security > Certificate
    13.  
      Main > Settings > Security > Certificate > CertificateSigningRequest
    14.  
      Main > Settings > Security > FIPS
    15.  
      Settings > Security > NetworkAccessControl
    16.  
      Main > Settings > Security > PasswordAge
    17.  
      Main > Settings > Security > Ports
    18.  
      Main > Settings > Security > SecurityLevel
    19.  
      Main > Settings > Security > Sessions
    20.  
      Main > Settings > Security > STIG
  22. 附录 U. Main > Support 命令
    1.  
      Support > Checkpoint
    2.  
      Support > Cleanup > CleanMonInvData
    3.  
      Support > Cleanup > RemoveShelfEntries
    4.  
      Support > Cleanup > ResetDIMMErrors
    5.  
      Support > Collect
    6.  
      Support > DataCollect
    7.  
      Support > Disk
    8.  
      Support > Errors
    9.  
      Support > FactoryReset
    10.  
      Support > FibreTransport
    11.  
      Support > ImportISO
    12.  
      Support > InfraServices
    13.  
      Support > InstantAccess
    14.  
      Support > iostat
    15.  
      Support > IPMI
    16.  
      Support > KillRemoteCall
    17.  
      Support > LogBrowser
    18.  
      Support > Logs
    19.  
      Support > Maintenance
    20.  
      Support > Messages
    21.  
      Support > NBDNA
    22.  
      Support > Nbperfchk
    23.  
      Support > NBSU
    24.  
      Support > Processes
    25.  
      Support > RAID
    26.  
      Support > Reboot
    27.  
      Support > RecoverStorage
    28.  
      Support > Service
    29.  
      Support > ShelfOrdering
    30.  
      Support > SHMCLI
    31.  
      Support > Show
    32.  
      Support > Shutdown
    33.  
      Support > Storage ClearReservations
    34.  
      Support > Storage SanityCheck
    35.  
      Support > Storage Show
    36.  
      Support > System
    37.  
      Support > Test

名称

Main > Support > ShelfOrdering — 重置或显示 52xx 设备上挂接的存储扩展架的顺序。

大纲

ShelfOrdering Reset

ShelfOrdering Show

描述

使用 Support > ShelfOrdering 命令，可重置或显示 52xx 设备上挂接的存储扩展架的顺序。

选项

ShelfOrdering Reset

用于重置挂接的存储扩展架的顺序。

使用 Reset 选项时，请注意以下事项：

  • 此命令将重置挂接的存储扩展架的数字顺序。当前分配给每个扩展架的扩展架 ID 可能会更改，并且不能复原。

  • 成功重置存储扩展架的顺序后，AutoSupport 服务将自动重新启动。在这段时间内，设备无法接收监控信息或警报。

ShelfOrdering Show

用于显示挂接的存储扩展架的当前顺序。