搜索 <book_title>...

Veritas NetBackup™ Appliance 命令参考指南

Last Published: 2023-11-27

Product(s): Appliances (5.3)

Platform: NetBackup Appliance OS

概述
1. 关于 NetBackup Appliance 命令行操作界面
2. 登录到 NetBackup Appliance 命令行操作界面
  1. 未配置设备上的命令限制
3. 使用 NetBackup Appliance 命令行操作界面
4. 关于 NetBackup Appliance 命令行操作界面命令视图
附录 A. Main > Appliance 命令
1. Appliance > Primary
2. Appliance > Media
3. Appliance > Management
4. Appliance > Remove
5. Appliance > ShowDedupPassword
6. Appliance > ShowIdentity
7. Appliance > Status
附录 B. Main > Manage > FibreChannel 命令
1. Manage > FibreChannel > Clean
2. Manage > FibreChannel > Configure
3. Manage > FibreChannel > Reset
4. Manage > FibreChannel > Scan
5. Manage > FibreChannel > Show
6. Manage > FibreChannel > Statistics
附录 C. Main > Manage > HighAvailability 命令
1. Manage > HighAvailability > AddNode
2. Manage > HighAvailability > AutoFix
3. Manage > HighAvailability > GetAssetTag
4. Manage > HighAvailability > RemoveNode
5. Manage > HighAvailability > Setup
6. Manage > HighAvailability > Status
7. Manage > HighAvailability > Switchover
附录 D. Main > Manage > Libraries 命令
1. Manage > Libraries > Configure
2. Manage > Libraries > Deny
3. Manage > Libraries > Down
4. Manage > Libraries > Inventory
5. Manage > Libraries > List
6. Manage > Libraries > Requests
7. Manage > Libraries > Reset
8. Manage > Libraries > Resubmit
9. Manage > Libraries > Up
附录 E. Main > Manage > Libraries > Advanced > ACS 命令
1. Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
2. Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
3. Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
4. Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
5. Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
6. Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
7. Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
8. Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
9. Manage > Libraries > Advanced > ACS > TestACS
10. Manage > Libraries > Advanced > ACS > ViewVMconf
附录 F. Main > Manage > License 命令
1. Manage > License
附录 G. Main > Manage > MountPoints 命令
1. Manage > MountPoints > List
2. Manage > MountPoints > Mount
3. Manage > MountPoints > Unmount
附录 H. Main > Manage > NetBackup CLI 命令
1. Manage > NetBackupCLI > AllowSelfService
2. Manage > NetBackupCLI > Create
3. Manage > NetBackupCLI > Delete
4. Manage > NetBackupCLI > List
附录 I. Main > Manage > OpenStorage 命令
1. Manage > OpenStorage > Install
2. Manage > OpenStorage > List
3. Manage > OpenStorage > Readme
4. Manage > OpenStorage > Share
5. Manage > OpenStorage > Uninstall
附录 J. Main > Manage > Software 命令
1. Manage > Software > Cancel
2. Manage > Software > Delete
3. Manage > Software > Download
4. Manage > Software > DownloadAnalyzer
5. Manage > Software > DownloadProgress
6. Manage > Software > Firmware
7. Manage > Software > Install
8. Manage > Software > List
9. Manage > Software > Readme
10. Manage > Software > Rollback
11. Manage > Software > Share
12. Manage > Software > UpgradeReadinessCheck
13. Manage > Software > UpgradeStatus
14. Manage > Software > VxUpdate
附录 K. Main > Manage > Storage 命令
1. Manage > Storage > Add
2. Manage > Storage > Create
3. Manage > Storage > Delete
4. Manage > Storage > Edit
5. Manage > Storage > Monitor
6. Manage > Storage > Move
7. Manage > Storage > Remove
8. Manage > Storage > Resize
9. Manage > Storage > Scan
10. Manage > Storage > Show
附录 L. Main > Manage > Tapes 命令
1. Manage > Tapes > Cleaning
2. Manage > Tapes > Delete
3. Manage > Tapes > Eject
4. Manage > Tapes > Freeze
5. Manage > Tapes > Inventory
6. Manage > Tapes > List
7. Manage > Tapes > ListNetBackupMedia
8. Manage > Tapes > Suspend
9. Manage > Tapes > Unfreeze
10. Manage > Tapes > Unsuspend
附录 M. Main > Monitor 命令
1. Monitor > Beacon
2. 监视 > 硬件
3. Monitor > MemoryStatus
4. Monitor > NetBackup
5. Monitor > NetworkStatus
6. Monitor > SDCS
7. Monitor > Top
8. Monitor > Uptime
9. Monitor > Who
附录 N. Main > Network 命令
1. Network > Configure
2. Network > Date
3. Network > DNS
4. Network > Gateway
5. Network > Hostname
6. Network > Hosts
7. Network > IPv4
8. Network > IPv6
9. Network > LinkAggregation
10. Network > NetStat
11. Network > NTPServer
12. Network > Ping
13. Network > SetProperty
14. Network > Show
15. Network > TimeZone
16. Network > TraceRoute
17. Network > Unconfigure
18. Network > VLAN
19. Network > WANOptimization
附录 O. Main > Network > Security 命令 (DeviceCert)
1. Network > Security > Export
2. Network > Security > Import
附录 P. Main > Reports 命令
1. Reports > Deduplication
2. Reports > Process
附录 Q. Main > Settings 命令
1. Settings > Deduplication
2. Settings > FibreTransport
3. Settings > iSCSI > Initiator
4. Settings > iSCSI > Interface
5. Settings > iSCSI > Target
6. Settings > LifeCycle
7. Settings > LogForwarding
8. Settings > NetBackup
9. Settings > NetBackup DNAT
10. Settings > NetBackup NATServers
11. 设置 > 密码
12. Settings > Share
13. Settings > SNMP
14. Settings > Sysctl
15. Settings > SystemLocale
附录 R. Main > Settings > Alerts 命令
1. Settings > Alerts > CallHome
2. Settings > Alerts > Email
3. Settings > Alerts > Hardware
4. Settings > Alerts > SNMP
5. Settings > Alerts > Transmission
附录 S. Main > Settings > Notifications 视图命令
1. Settings > Notifications > LoginBanner
附录 T. Main > Settings > Security 命令
1. Settings > Security > Antimalware
2. Settings > Security > Authorization
3. Settings > Security > Authentication > AccountStatus
4. Settings > Security > Authentication > ActiveDirectory
5. Main > Settings > Security > Authentication > CIFSShare
6. Settings > Security > Authentication > LDAP
7. Settings > Security > Authentication > LocalUser
8. Settings > Security > Authentication > MFA
9. Settings > Security > Authentication > SingleSignOn
10. Settings > Security > Authentication > SmartCard > SSH
11. Settings > Security > Authentication > SmartCard
12. Main > Settings > Security > Certificate
13. Main > Settings > Security > Certificate > CertificateSigningRequest
14. Main > Settings > Security > FIPS
15. Settings > Security > NetworkAccessControl
16. Main > Settings > Security > PasswordAge
17. Main > Settings > Security > Ports
18. Main > Settings > Security > SecurityLevel
19. Main > Settings > Security > Sessions
20. Main > Settings > Security > STIG
附录 U. Main > Support 命令
1. Support > Checkpoint
2. Support > Cleanup > CleanMonInvData
3. Support > Cleanup > RemoveShelfEntries
4. Support > Cleanup > ResetDIMMErrors
5. Support > Collect
6. Support > DataCollect
7. Support > Disk
8. Support > Errors
9. Support > FactoryReset
10. Support > FibreTransport
11. Support > ImportISO
12. Support > InfraServices
13. Support > InstantAccess
14. Support > iostat
15. Support > IPMI
16. Support > KillRemoteCall
17. Support > LogBrowser
18. Support > Logs
19. Support > Maintenance
20. Support > Messages
21. Support > NBDNA
22. Support > Nbperfchk
23. Support > NBSU
24. Support > Processes
25. Support > RAID
26. Support > Reboot
27. Support > RecoverStorage
28. Support > Service
29. Support > ShelfOrdering
30. Support > SHMCLI
31. Support > Show
32. Support > Shutdown
33. Support > Storage ClearReservations
34. Support > Storage SanityCheck
35. Support > Storage Show
36. Support > System
37. Support > Test

名称

Main > Settings > NetBackup DNAT — 在 NetBackup Appliance 主服务器和介质服务器上启用/禁用目标网络地址转换 (DNAT)

大纲

Enable

Disable

Show

描述

此命令用于在与启用 NAT 的客户端通信的 NetBackup Appliance 主服务器和介质服务器上启用或禁用 DNAT。

选项

NetBackup DNAT Enable: 在与启用 DNAT 的客户端通信的 NetBackup Appliance 主服务器或介质服务器上启用 DNAT。
注意:
在 NetBackup Appliance 主服务器或介质服务器上启用 DNAT 之前，请检查 NetBackup 域中的所有客户端是否都支持网络地址转换 (NAT)。如果所有客户端都不支持 NAT，请与 Veritas 支持联系以获取 EEB，从而防止出现内存泄漏问题。

NetBackup DNAT Disable: 在 NetBackup Appliance 主服务器或介质服务器上禁用 DNAT。

NetBackup DNAT Show: 显示设备上 NetBackup DNAT 的状态。

示例

以下是当您运行 Settings > NetBackup DNAT Enable 命令时显示的信息的示例。

Settings> NetBackup DNAT Enable
>> If you have Network Address Translation (NAT) clients and 
non-NAT clients, you must first contact Veritas Support
 to obtain an EEB to prevent any possible memory leak issues.
If you have only NAT clients, you may continue with the configuration. 
Do you want to continue? [yes, no](yes)
>> Enabling DNAT requires restarting NetBackup services, 
which may take several minutes. 
Do you want to continue? [yes, no](yes)
- [Info] DNAT has been enabled successfully.

以下是当您运行 Settings > NetBackup DNAT Disable 命令时显示的信息的示例。

Settings> NetBackup DNAT Disable 
>> Disabling DNAT requires restarting NetBackup services, which may 
take several minutes. Do you want to continue? [yes, no](yes)
- [Info] DNAT has been disabled successfully.

要在客户端上启用或禁用 DNAT，必须更新 ACCEPT_REVERSE_CONNECTION 标志。可使用 /usr/openv/netbackup/bin/admincmd/bpsetconfig 实用程序启用或禁用 DNAT，如下所示。

要在客户端上启用 DNAT，请使用以下命令：

$ bpsetconfig
bpsetconfig> ACCEPT_REVERSE_CONNECTION=True

要在客户端上禁用 DNAT，请使用以下命令：

$ bpsetconfig
bpsetconfig> ACCEPT_REVERSE_CONNECTION=False

更新 ACCEPT_REVERSE_CONNECTION 标志后，请确保运行以下命令来停止并重新启动 NetBackup 服务：

在 UNIX 客户端上：
/usr/openv/netbackup/bin/bp.kill_all
/usr/openv/netbackup/bin/bp.start_all
在 Windows 客户端上：
<install_path>\NetBackup\bin\bpdown
<install_path>\NetBackup\bin\bpup