Veritas NetBackup Snapshot Client Administrator's Guide
- Snapshot Client features
- About snapshot basics
- Off-host backup overview
- Off-host backup methods
- About alternate client backup
- Snapshot Client requirements
- Policy configuration
- Selecting the snapshot method
- Configuration parameters for Snapshot Client
- About using alternate client backup
- Configuring alternate client backup
- Policy configuration tips
- About disabling snapshots
- FlashBackup configuration
- Instant Recovery configuration
- About Instant Recovery
- About sizing the cache for Instant Recovery copy-on-write snapshots
- About configuring VxVM
- About storage lifecycle policies for snapshots
- Network Attached Storage (NAS) snapshot configuration
- Configuration of software-based snapshot methods
- Software-based snapshot methods
- Cache device requirements
- About VxFS_Checkpoint
- About VxVM
- About FlashSnap
- About VVR
- About VSS
- Software-based snapshot methods
- Support for Cluster Volume Manager Environments (CVM)
- Configuration of snapshot methods for disk arrays
- About the new disk array snapshot methods
- Disk array configuration tasks
- OS-specific configuration tasks
- About VSS configuration (Windows)
- About EMC CLARiiON arrays
- Configuring NetBackup to access the CLARiiON array
- Configuring a NetBackup policy for a CLARiiON array method
- About EMC Symmetrix arrays
- About configuration for EMC_TimeFinder_Mirror
- About configuration for EMC_TimeFinder_Clone
- About HP EVA arrays
- Verifying connectivity from clients to array using SSSU 5.0
- About IBM DS6000 and DS8000 arrays
- Configuring NetBackup to access the IBM DS6000 or DS8000 array
- About IBM DS4000 array
- About Hitachi SMS/WMS/AMS, USP/NSC, USP-V/VM
- Hitachi array software requirements
- About HP-XP arrays
- About array troubleshooting
- Troubleshooting issues pertaining to all arrays
- Troubleshooting IBM DS6000 and DS8000 arrays
- Troubleshooting IBM4000 arrays
- Troubleshooting Hitachi arrays
- Notes on Media Server and Third-Party Copy methods
- Backup and restore procedures
- About restores from a FlashBackup backup
- Instant Recovery restore features
- About Instant Recovery: block-level restore
- About Instant Recovery: file promotion
- About Instant Recovery: Fast File Resync (Windows clients only)
- About Instant Recovery: point in time rollback
- About configurations for restore
- About restoring from a disk snapshot
- Logging directories for UNIX platforms
- Logging folders for Windows platforms
- FlashBackup and status code 13
- Appendix A. Managing nbu_snap (Solaris)
- Appendix B. Overview of snapshot operations
- Appendix C. NetBackup integration with CloudPoint for snapshot managment
Configuring a NetBackup policy for Hitachi_ShadowImage or Hitachi_CopyOnWrite
For general help setting up a NetBackup policy in the NetBackup Administration Console, refer to the NetBackup Administrator's Guide, Volume I.
The term "clone LUNs," as used in this procedure, refers to the Hitachi_ShadowImage method. For the Hitachi_CopyOnWrite method, the term "clone LUNs" can be replaced with "snapshot LUNs."
To configure a NetBackup policy for Hitachi_ShadowImage or Hitachi_CopyOnWrite
- In the NetBackup Administration Console, click the Perform snapshot backups box on the policy Attributes tab.
- Click the Options option to display the Snapshot Options dialog box.
- In the Snapshot method pull-down list, select Hitachi_ShadowImage or Hitachi_CopyOnWrite.
- In the Snapshot Resources pane, click Add.
NetBackup uses the information in the Snapshot Resources pane to correctly rotate through the designated LUNs when performing a ShadowImage (or CopyOnWrite) backup. After all clone LUNs have been used in a backup, NetBackup automatically determines which clone is the oldest. NetBackup expires the oldest clone so that it can be reused for the current backup. If that clone represents the only backup image copy, NetBackup also expires the backup image associated with the clone.
Note that the policy's Backup Selections list must specify one or more source LUNs for which snapshots are created for the backup. For each source LUN in the policy Backup Selections list, you must supply a serial number and unique IDs.
If the snapshot resources specified in the Snapshot Resources pane do not match with the LUN IDs specified through the backup selection entries then the NetBackup Hitachi storage array plug-in will discover the available target device and use it for snapshot.
- In the Add Snapshot Resource dialog box, enter the array's serial number in the Array Serial # field.
- Enter the unique ID for the source LUN in the Source Device field.
The ID must be entered without leading zeroes. For example, if the LUN ID is 0110, enter 110 in the Source Device field.
- Enter the unique IDs for the clone LUNs (for Hitachi_ShadowImage method) or the snapshot LUNs (for Hitachi_CopyOnWrite) in the Snapshot Device(s) field. To enter multiple IDs, place a semicolon between them.
The ID must be without leading zeroes. For example, if the LUN ID is 0111, enter 111 in the Snapshot Device(s) field.
Note the following:
The LUNs must be unmasked to the client (or alternate client) before you start a backup.
For Instant Recovery backups, the Snapshot Device(s) entries determine where and in what order the snapshots are retained.