Veritas NetBackup Snapshot Client Administrator's Guide
- Snapshot Client features
- About snapshot basics
- Off-host backup overview
- Off-host backup methods
- About alternate client backup
- Snapshot Client requirements
- Policy configuration
- Selecting the snapshot method
- Configuration parameters for Snapshot Client
- About using alternate client backup
- Configuring alternate client backup
- Policy configuration tips
- About disabling snapshots
- FlashBackup configuration
- Instant Recovery configuration
- About Instant Recovery
- About sizing the cache for Instant Recovery copy-on-write snapshots
- About configuring VxVM
- About storage lifecycle policies for snapshots
- Network Attached Storage (NAS) snapshot configuration
- Configuration of software-based snapshot methods
- Software-based snapshot methods
- Cache device requirements
- About VxFS_Checkpoint
- About VxVM
- About FlashSnap
- About VVR
- About VSS
- Software-based snapshot methods
- Support for Cluster Volume Manager Environments (CVM)
- Configuration of snapshot methods for disk arrays
- About the new disk array snapshot methods
- Disk array configuration tasks
- OS-specific configuration tasks
- About VSS configuration (Windows)
- About EMC CLARiiON arrays
- Configuring NetBackup to access the CLARiiON array
- Configuring a NetBackup policy for a CLARiiON array method
- About EMC Symmetrix arrays
- About configuration for EMC_TimeFinder_Mirror
- About configuration for EMC_TimeFinder_Clone
- About HP EVA arrays
- Verifying connectivity from clients to array using SSSU 5.0
- About IBM DS6000 and DS8000 arrays
- Configuring NetBackup to access the IBM DS6000 or DS8000 array
- About IBM DS4000 array
- About Hitachi SMS/WMS/AMS, USP/NSC, USP-V/VM
- Hitachi array software requirements
- About HP-XP arrays
- About array troubleshooting
- Troubleshooting issues pertaining to all arrays
- Troubleshooting IBM DS6000 and DS8000 arrays
- Troubleshooting IBM4000 arrays
- Troubleshooting Hitachi arrays
- Notes on Media Server and Third-Party Copy methods
- Backup and restore procedures
- About restores from a FlashBackup backup
- Instant Recovery restore features
- About Instant Recovery: block-level restore
- About Instant Recovery: file promotion
- About Instant Recovery: Fast File Resync (Windows clients only)
- About Instant Recovery: point in time rollback
- About configurations for restore
- About restoring from a disk snapshot
- Logging directories for UNIX platforms
- Logging folders for Windows platforms
- FlashBackup and status code 13
- Appendix A. Managing nbu_snap (Solaris)
- Appendix B. Overview of snapshot operations
- Appendix C. NetBackup integration with CloudPoint for snapshot managment
Configuring a NetBackup policy for IBM_DiskStorage_FlashCopy
For general help setting up a NetBackup policy in the NetBackup Administration Console, refer to the NetBackup Administrator's Guide, Volume I.
The following procedure focuses on the IBM_DiskStorage_FlashCopy method and its parameters.
To configure a NetBackup policy for IBM_DiskStorage_FlashCopy
- In the NetBackup Administration Console, click the Perform snapshot backups box on the policy Attributes tab.
- Click the Options option to display the Snapshot Options dialog box.
- In the Snapshot method pull-down list, select IBM_DiskStorage_FlashCopy.
- If needed, set Wait for flashcopy operation to complete to 1.
By default (0), the backup does not wait for the FlashCopy operation to complete. If the backup begins before the FlashCopy operation completes, database performance on the client (such as Oracle) may be affected until the FlashCopy is complete. A setting of 1 means that NetBackup waits for the FlashCopy to complete before the backup begins, to avoid any performance issues on the client.
Note that a setting of 1 may cause the backup elapsed time to increase significantly. The primary (production) volume may not be accessible until the FlashCopy command completes.
- On the Snapshot Options dialog box in the Snapshot Resources pane, click Add.
NetBackup uses the information in the Snapshot Resources pane to correctly rotate through the clone LUNs when performing a FlashCopy clone backup. After all clone LUNs have been used in a backup, NetBackup automatically determines which clone is the oldest. NetBackup expires the oldest clone so that it can be reused for the current backup. If that clone represents the only backup image copy, NetBackup also expires the backup image associated with the clone.
Note that the policy Backup Selections determine one or more source LUNs for which snapshots are taken for backup. For each source LUN that is specified in the policy Backup Selections list, you must provide the information detailed in the following steps.
- In the Add Snapshot Resource dialog box, enter the array's serial number in the Array Serial Number field.
- Enter the unique ID for the source LUN in the Source Device field.
- Enter the unique IDs for the clone LUNs in the Snapshot Device(s) field. To enter multiple IDs, place a semicolon between them.
Note the following:
The clone LUNs must be unmasked to the client (or alternate client) before you start a backup.
For Instant Recovery backups, the Snapshot Device(s) entries determine where and in what order the snapshots are retained.