请输入搜索词进行查询
搜索 <book_title>...
Veritas NetBackup™ Appliance 命令参考指南
Last Published:
2019-11-04
Product(s):
Appliances (3.2)
Platform: NetBackup Appliance OS
- 概述
- 附录 A. Main > Appliance 命令
- 附录 B. Main > Manage > FibreChannel 命令
- 附录 C. Main > Manage > HighAvailability 命令
- 附录 D. Main > Manage > Libraries 命令
- 附录 E. Main > Manage > Libraries > Advanced > ACS 命令
- Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
- Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
- Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
- Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
- Manage > Libraries > Advanced > ACS > TestACS
- Manage > Libraries > Advanced > ACS > ViewVMconf
- 附录 F. Main > Manage > License 命令
- 附录 G. Main > Manage > MountPoints 命令
- 附录 H. Main > Manage > NetBackup CLI 命令
- 附录 I. Main > Manage > OpenStorage 命令
- 附录 J. Main > Manage > Software 命令
- Manage > Software > Cancel
- Manage > Software > Delete
- Manage > Software > Download
- Manage > Software > DownloadProgress
- Manage > Software > Firmware
- Manage > Software > Install
- Manage > Software > List
- Manage > Software > Readme
- Manage > Software > Rollback
- Manage > Software > Share
- Manage > Software > UpgradeStatus
- Manage > Software > VxUpdate
- 附录 K. Main > Manage > Storage 命令
- 附录 L. Main > Manage > Tapes 命令
- 附录 M. Main > Manage > Certificates 命令
- 附录 N. Main > Monitor 命令
- 附录 O. Main > Network 命令
- Network > Configure
- Network > Date
- Network > DNS
- Network > Gateway
- Network > Hostname
- Network > Hosts
- Network > IPv4
- Network > IPv6
- Network > LinkAggregation
- Network > NetStat
- Network > NTPServer
- Network > Ping
- Network > SetProperty
- Network > Show
- Network > TimeZone
- Network > TraceRoute
- Network > Unconfigure
- Network > VLAN
- Network > WANOptimization
- 附录 P. Main > Network > Security 命令 (IPsec)
- 附录 Q. Main > Reports 命令
- 附录 R. Main > Settings 命令
- Settings > Cloud
- Settings > Deduplication
- Settings > FibreTransport
- Settings > iSCSI > Initiator
- Settings > iSCSI > Interface
- Settings > iSCSI > Target
- Settings > LogForwarding
- Settings > LifeCycle
- Settings > NetBackup
- Settings > Password
- Settings > Share
- Settings > SNMP polling
- Settings > Sysctl
- Settings > SystemLocale
- Settings > NetBackup DNAT
- 附录 S. Main > Settings > Alerts 命令
- 附录 T. Main > Settings > Notifications 视图命令
- 附录 U. Main > Settings > Security 命令
- Settings > Security > Authorization
- Settings > Security > Authentication > ActiveDirectory
- Settings > Security > Authentication > Kerberos
- Settings > Security > Authentication > LDAP
- Settings > Security > Authentication > LocalUser
- Main > Settings > Security > Certificate
- Main > Settings > Security > FIPS
- Main > Settings > Security > Ports
- Main > Settings > Security > STIG
- 附录 V. Main > Support 命令
- Support > Checkpoint
- Support > Cleanup > RemoveShelfEntries
- Support > Cleanup > ResetDIMMErrors
- Support > Collect
- Support > DataCollect
- Support > Disk
- Support > Errors
- Support > FactoryReset
- Support > FibreTransport
- Support > InfraServices
- Support > iostat
- Support > IPMI
- Support > KillRemoteCall
- Support > Logs
- Support > Maintenance
- Support > Messages
- Support > NBDNA
- Support > nbperfchk
- Support > NBSU
- Support > Processes
- Support > RAID
- Support > Reboot
- Support > RecoverStorage
- Support > Service
- Support > ServiceAllowed
- Support > Show
- Support > Shutdown
- Support > Storage ClearReservations
- Support > Storage Reset
- Support > Storage SanityCheck
- Support > Test
名称
Main > Network > VLAN — 标记 VLAN，查看其属性和状态，或删除已标记的 VLAN。
大纲
VLAN Delete VLANID
VLAN Show Properties Interfaces InterfaceNames
VLAN Show Status Interfaces InterfaceNames
VLAN Tag VLANIDInterfaceNames[IPAddress][Netmask]
描述
使用这些命令可配置和管理现有网络环境中的设备的 VLAN。
要使用结合接口或物理接口标记 VLAN，请遵从以下准则
确保已插入所选接口或以太网设备。
验证所选接口不是结合的一部分。
所选接口不能有配置的 IP 地址。如果已对所选接口配置了 IP 地址，必须首先取消配置 IP 地址然后对其标记 VLAN。要取消配置 IP 地址，请运行 Network > Unconfigure 命令。
注意:
仅能通过 NetBackup Appliance 命令行操作界面而非 NetBackup Appliance 网页操作界面将 VLAN 标记到专用网络接口（例如 eth0）。
使用 VLAN Show 命令选项查看网络接口的属性和状态。
选项
- VLAN Delete VLANID
删除基于协议的 VLAN。其中，VLANID 是已标记 VLAN 的数字标识符。
如果已对 VLAN 接口配置了 IP 地址，必须首先取消配置 IP 地址然后删除 VLAN。
- VLAN Show Properties Interfaces InterfaceNames
查看 VLAN 的所有属性，其中 InterfaceNames 是 VLAN 标记到的接口的名称。如果没有提供 [InterfaceNames] 参数的值，则该命令将显示所有可用网络接口的属性。包括的某些属性类型有 MAC 地址、速度和端口类型。
- VLAN Show Status Interfaces InterfaceNames
查看 VLAN 的状态。VLAN 状态可以是 PLUGGED 或 UNPLUGGED。其中，InterfaceNames 是 VLAN 标记到的接口的名称。
- VLAN Tag VLANIDInterfaceNames [IPAddress] [Netmask]
将 VLAN 标记到物理接口或结合。其中，VLANID 是 VLAN 标识符，它是一个数值且在 1 - 4094 之间。InterfaceNames 是要将 VLAN 标记到的接口的名称。[IPAddress] 可以是 IPv4 或 IPv6 地址，且 [Netmask] 是 IPv4 的网络掩码或 IPv6 的前缀长度。VLANID 和 InterfaceNames 是必备变量，而 [IPAddress] 和 [Netmask] 是可选参数。
示例
以下是运行 Main > Network > VLAN Show Properties 命令时显示的信息的示例。
nb-appliance.Network> VLAN Show properties Card: vlan12 [ PLUGGED|UP ] BOOTPROTO : |static | DESCRIPTION : |test | DEVICE : |vlan12 | ETHERDEVICE : |eth1 | ETHTOOL_OPTIONS : |undef | IPADDR : |10.10.10.10 | MTU : |1400 | NETMASK : |255.255.255.0 | NETWORK : |undef | REMOTE_IPADDR : |undef | STARTMODE : |auto | USERCONTROL : |no | VLAN : |yes | BUS_ID : |undef | FLAGS : |RBMU | ID : |12 | LINK : |yes | MAC : |00:50:56:B5:74:13 | MASTER : |undef | MODEL : |undef | PORT_TYPE : |Twisted Pair | SERIAL : |undef | SKIP_ADDITIONAL_DISCOVERY : |0 | SKIP_LINKSTATE_DISCOVERY : |0 | SPEED : |1Gb/s | VIRTUAL_DEV : |undef | VLANCOUNT : |0 | ADMINPORT : |No | VIRTUAL : |No | IPADDR_V6 : |undef |