Veritas NetBackup™ Appliance Commands Reference Guide
- Overview
- Appendix A. Main > Appliance commands
- Appendix B. Main > Manage > FibreChannel commands
- Appendix C. Main > Manage > HighAvailability commands
- Appendix D. Main > Manage > Libraries commands
- Appendix E. Main > Manage > Libraries > Advanced > ACS commands
- Manage > Libraries > Advanced > ACS > ACS_CSI_HOSTPORT
- Manage > Libraries > Advanced > ACS > ACS_SEL_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_SSI_HOSTNAME
- Manage > Libraries > Advanced > ACS > ACS_SSI_INET_PORT
- Manage > Libraries > Advanced > ACS > ACS_SSI_SOCKET
- Manage > Libraries > Advanced > ACS > ACS_TCP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > ACS_UDP_RPCSERVICE
- Manage > Libraries > Advanced > ACS > API_BARCODE_RULES
- Manage > Libraries > Advanced > ACS > TestACS
- Manage > Libraries > Advanced > ACS > ViewVMconf
- Appendix F. Main > Manage > License commands
- Appendix G. Main > Manage > MountPoints commands
- Appendix H. Main > Manage > NetBackup CLI commands
- Appendix I. Main > Manage > OpenStorage commands
- Appendix J. Main > Manage > Software commands
- Manage > Software > Cancel
- Manage > Software > Delete
- Manage > Software > Download
- Manage > Software > DownloadProgress
- Manage > Software > Firmware
- Manage > Software > Install
- Manage > Software > List
- Manage > Software > LiveUpdateClients
- Manage > Software > Readme
- Manage > Software > Rollback
- Manage > Software > Share
- Manage > Software > UpgradeStatus
- Appendix K. Main > Manage > Storage commands
- Appendix L. Main > Manage > Tapes commands
- Appendix M. Main > Manage > Certificates commands
- Appendix N. Main > Monitor commands
- Appendix O. Main > Network commands
- Network > Configure
- Network > Date
- Network > DNS
- Network > Gateway
- Network > Hostname
- Network > Hosts
- Network > IPv4
- Network > IPv6
- Network > LinkAggregation
- Network > NetStat
- Network > NTPServer
- Network > Ping
- Network > SetProperty
- Network > Show
- Network > TimeZone
- Network > TraceRoute
- Network > Unconfigure
- Network > VLAN
- Network > WANOptimization
- Appendix P. Main > Network > Security (IPsec) commands
- Appendix Q. Main > Reports commands
- Appendix R. Main > Settings commands
- Settings > Cloud
- Settings > Deduplication
- Settings > FibreTransport
- Settings > iSCSI > Initiator
- Settings > iSCSI > Interface
- Settings > iSCSI > Target
- Settings > LogForwarding
- Settings > LifeCycle
- Settings > LiveUpdateServer
- Settings > NetBackup
- Settings > Password
- Settings > Share
- Settings > SNMP polling
- Settings > Sysctl
- Settings > SystemLocale
- Appendix S. Main > Settings > Alerts commands
- Appendix T. Main > Settings > Notifications view commands
- Appendix U. Main > Settings > Security commands
- Settings > Security > Authorization
- Settings > Security > Authentication > ActiveDirectory
- Settings > Security > Authentication > Kerberos
- Settings > Security > Authentication > LDAP
- Settings > Security > Authentication > LocalUser
- Main > Settings > Security > Ports
- Main > Settings > Security > STIG
- Main > Settings > Security > FIPS
- Appendix V. Main > Support commands
- Support > Checkpoint
- Support > Cleanup > RemoveShelfEntries
- Support > Cleanup > ResetDIMMErrors
- Support > Collect
- Support > DataCollect
- Support > Disk
- Support > Errors
- Support > FactoryReset
- Support > FibreTransport
- Support > InfraServices
- Support > iostat
- Support > IPMI
- Support > KillRemoteCall
- Support > Logs
- Support > Maintenance
- Support > Messages
- Support > NBDNA
- Support > nbperfchk
- Support > NBSU
- Support > Processes
- Support > RAID
- Support > Reboot
- Support > RecoverStorage
- Support > Service
- Support > ServiceAllowed
- Support > Show
- Support > Shutdown
- Support > Storage ClearReservations
- Support > Storage Reset
- Support > Storage SanityCheck
- Support > Test
About the commands under the Support view
From the Main > Support view you can perform the following functions:
Collect appliance logs and data for support interactions through the DataCollect command.
Manage system checkpoints and IPMI operations.
Gather disk information.
Display NetBackup errors.
Create and Manage checkpoints.
Reset the appliance to factory default settings.
Show the appliance logs.
Display the messages file.
Restart your appliance.
Turn off your appliance.
Share, unshare, and set the level of debug logs.
Display debugging information from the Vxlog files.
Restart a service on a host.
Upload a set of log files that are based on a timed duration of four hours.
Create and send a .tar file of the logs based on the job ID.
Create and send a .tar file of the logs based on the time the log files were created.
Test the current status of the various appliance components.
The following table summarizes all of the commands that are available in the NetBackup Support view.
Table: Main > Support view commands
Command | Explanation |
|---|---|
CheckPoint | Manage system checkpoints. |
Cleanup | Clean or reset specific appliance monitoring data. |
DataCollect | Gather the device logs. |
Disk | Gather and displays information about the local disk layout and usage. See Support > Disk. |
Errors | Display the problem entries from the previous day in the NetBackup logs. |
FactoryReset | Reset the appliance to factory default settings. See Support > FactoryReset . |
InfraServices | Display and control the infrastructure services. See Support > InfraServices . |
iostat | Monitor the system input and output device loading |
IPMI | Manage the IPMI operations. |
KillRemoteCall | Terminate remote calls on peer compute nodes. |
Logs | From this command you can perform the following tasks:
See Support > Logs. |
Maintenance | Enable you to open an interactive shell menu that you can use to troubleshoot or manage underlying operating system tasks. |
Messages | Display the message file. See Support > Messages . |
NBDNA | Create and remove network traces with the NetBackup Domain Network Analyzer (NBDNA) utility. See Support > NBDNA . |
Nbperfchk | Measure the read and write speeds of a disk array. |
NBSU | Manage NetBackup supported data files. See Support > NBSU . |
Processes | Display the status of the current processes. See Support > Processes . |
Reboot | Restart the system. See Support > Reboot . |
RecoverStorage | View or purge any storage recovered during a reimage. |
Service | Stop or restarts a service on an appliance Linux host. |
ServiceAllowed | Set specific components of a Primary or an Expansion Storage Shelf to the Service Allowed mode so that service can be performed on those units. |
Shutdown | Power the system off. See Support > Shutdown . |
Storage | Use this command to perform the following tasks:
|
Test | Test the current status of the various appliance components. See Support > Test. |