Veritas™ 5260 Appliance Hardware Installation Guide

Last Published:
Product(s): Appliances (Version Not Specified)
Platform: Veritas 5260
  1. Hardware overview
    1.  
      About the appliance and the storage shelves
    2.  
      Appliance drives
    3. About the 5260 Appliance control panel
      1.  
        About the System Status LED states
      2.  
        About the Power button LED states
      3.  
        About the integrated BMC beep codes
    4.  
      Appliance rear panel
    5.  
      Storage shelf disk drives
    6.  
      Storage shelf control panel
    7.  
      Storage shelf rear panel
    8.  
      Cables
    9.  
      About IPMI configuration
    10.  
      Product documentation
  2. Preinstallation requirements
    1.  
      Customer-provided environment and supplies
    2.  
      Appliance shipping container contents
    3.  
      Storage shelf shipping container contents
    4.  
      Best practices for rack installation
    5.  
      Determining rack locations
    6.  
      Storage shelf rack requirements
    7.  
      Heat dissipation
    8.  
      Verifying SAS-3 cable length
    9.  
      Prerequisites for IPMI configuration
  3. Installation procedures
    1.  
      Installing the storage shelf rack rails
    2.  
      Installing the storage shelf into a rack
    3.  
      Installing the appliance rack rails
    4.  
      Installing the appliance into a rack
    5.  
      Understanding appliance and storage shelf connections
    6.  
      Connecting an appliance to one storage shelf
    7.  
      Connecting an appliance to more than one storage shelf
  4. Next steps after installation
    1.  
      Connecting the network cables
    2.  
      Connecting the power cords
    3.  
      Turning on the hardware and verifying operation
    4.  
      Configuring the Veritas Remote Management Interface from a Flex Appliance
    5.  
      Configuring the Veritas Remote Management Interface using laptop
    6.  
      Accessing and using the Veritas Remote Management interface
  5. Appendix A. Adding one or more storage shelves to an operating appliance that does not have any storage shelves
    1.  
      Overview
    2.  
      Preparing the appliance
    3.  
      Removing the appliance cover
    4.  
      Installing the Expansion Storage Kit components
    5.  
      Replacing the appliance cover
    6. Connecting the storage shelves to the appliance
      1.  
        Connecting one storage shelf to an appliance
      2.  
        Connecting two storage shelves to an appliance
      3.  
        Connecting three storage shelves to an appliance
      4.  
        Connecting four storage shelves to an appliance
      5.  
        Connecting the fifth storage shelf to an appliance
      6.  
        Connecting the sixth storage shelf to an appliance
  6. Appendix B. Adding storage shelves to an operating appliance that has at least one storage shelf attached
    1.  
      Overview
    2.  
      Additional storage shelf scenarios
    3. Recabling to connect additional storage shelves
      1.  
        Connecting additional shelves to an appliance that already has one operating shelf
      2.  
        Connecting additional shelves to an appliance that already has two operating shelf
      3.  
        Connecting additional shelves to an appliance that already has three operating shelf
  7. Appendix C. Configuring the disk space for new Flex Expansion Storage Shelves
    1.  
      Adding the disk space of an Expansion Storage Shelf from the Flex Appliance Console
  8.  
    Index

Removing the appliance cover

The system ships from the factory with the front system cover and back system cover screwed to the chassis. A total of four screws, one on each side of the front cover and one on each side of the back cover, need to be removed to detach each top cover panel from the chassis.

Note:

This service will require the removal of the front panel.

Use the following procedures to remove the cover from the appliance.

To remove the appliance cover panels

  • For each top cover panel:

    • While pushing down on both the left and right buttons of the given top panel (see Letter A), slide the top cover panel towards the front (front panel) or back (back panel) of the chassis (see Letter B).

    • Carefully lift the top cover panel up and away from the chassis.

    Note:

    Each top cover panel can slide along the chassis base for 10 mm and then needs to be lifted.