Veritas Access 3340 Appliance Hardware Installation Guide

Last Published:
Product(s): Appliances (Version Not Specified)
Platform: 3340
  1. Overview
    1.  
      Supported software
    2.  
      Access 3340 compute node and 5U84 storage shelves
    3.  
      Access 3340 compute node disk drives
    4.  
      Access 3340 compute node control panel
    5.  
      Access 3340 compute node rear panel
    6.  
      5U84 storage shelf drawers and disk drives
    7.  
      5U84 storage shelf control panel
    8.  
      5U84 storage shelf rear panel
    9.  
      5U84 storage shelf RAID controller
    10.  
      5U84 storage shelf Expansion module
    11.  
      Cables and connectors
  2. Pre-installation requirements
    1.  
      Customer-provided environment and supplies
    2.  
      Storage shelf shipping container contents
    3.  
      Compute node shipping container contents
    4.  
      Dimensions and determining rack locations
    5.  
      Best practices for rack installation
    6.  
      Heat dissipation guidelines
    7.  
      Cable length verification
    8.  
      Prerequisites for IPMI configuration
  3. Hardware installation procedures
    1.  
      Overview
    2.  
      Installing a storage shelf
    3.  
      Installing disk drives into a storage shelf
    4.  
      Installing the storage shelf bezels
    5.  
      Installing the compute node rack rails
    6.  
      Installing the compute node into a rack
    7.  
      Connecting the hardware
    8.  
      Connecting Access nodes to the network
    9.  
      Connecting the power cords to the hardware
    10.  
      Turning on the hardware and verifying operation
    11.  
      Configuring the IPMI port from the Access Appliance shell menu
    12.  
      Accessing and using the Veritas Remote Management interface
  4. Appendix A. Adding storage shelves to an operating appliance that does not have any storage shelves
    1.  
      Turning off the existing hardware
    2.  
      Installing the hardware
    3.  
      Connecting one Expansion shelf to the Primary shelf
    4.  
      Connecting two Expansion shelves to the Primary shelf
    5.  
      Connecting three Expansion shelves to the Primary shelf
  5. Appendix B. Adding storage shelves to an operating appliance that has at least one operating storage shelf
    1.  
      Turning off the existing hardware
    2.  
      Installing the hardware
    3.  
      Connecting one Expansion shelf to a system that has one existing Expansion shelf
    4.  
      Connecting two Expansion shelves to a system that has one existing Expansion shelf
    5.  
      Connecting one Expansion shelf to a system that has two existing Expansion shelves
  6. Appendix C. Configuring the disk space after adding one or more new Expansion Storage Shelves
    1.  
      Adding the disk space of an Expansion Storage Shelf from the Access 3340 Appliance shell menu

Storage shelf shipping container contents

Each storage shelf container includes other boxes and contents as follows.

  • Open Me First envelope, containing:

    • Deployment plan that provides basic information and links to detailed information

    • Cable straps

  • Envelope, containing;

    • Warranty agreement

    • Environmental compliance statement

  • Hardware cable connections poster

  • Rack templates

  • Rack rails and mounting hardware

  • Two SAS-3 cables with each Expansion shelf

  • Two power cords

  • One bezel and four 2mm Hex screws for each drawer

The disk drives ship separately from the storage shelves. Each disk drive shipping container includes 42 disk drive slots.

Each Access 3340 storage disk drive box includes one carrier with a blank. In the top drawer this blank carrier is inserted into slot 41. In the bottom drawer this blank carrier is inserted into slot 83.

After you have installed the storage shelves into a rack, you should install the disk drives into the drawer.