NetBackup™ NAS Administrator's Guide
- Section I. About NAS backups
- Section II. Using NAS-Data-Protection (D-NAS)
- D-NAS overview
- Pre-requisites for D-NAS configuration
- Configure D-NAS policy for NAS volumes
- Using accelerator
- Replication using D-NAS policy
- Restoring from D-NAS backups
- Troubleshooting
- Troubleshooting
- Setting the log level
- Logging directories for Linux platforms
- Logging folders for Windows platforms
- Restore from a snapshot fails with status 133
- Backup from snapshot fails with error 50
- Backup from snapshot parent job fails with error 4213: Snapshot import failed
- Backup host pool creation fails with the error "Failed to fetch host list"
- Snapshot job fails and the snapshot command does not recognize the volume name
- Accelerator enabled incremental backup of NetApp NAS volume
- Snapshot method: Auto
- Section III. Section 3
- Introduction to NetBackup for NDMP
- About NetBackup for NDMP
- About Network Data Management Protocol (NDMP)
- Types of NDMP backup
- About NDMP policies in NetBackup
- About NetBackup storage units
- About assigning tape drives to different hosts
- About the NDMP backup process
- About the NDMP restore process
- About Direct Access Recovery (DAR)
- Snapshot Client assistance
- About NDMP multiplexing
- About NDMP support for Replication Director
- Limitations of Replication Director with NDMP
- About NDMP support for NetApp clustered Data ONTAP (cDOT)
- Installation Notes for NetBackup for NDMP
- Configuring NDMP backup to NDMP-attached devices
- About configuring NDMP-attached devices
- Authorizing NetBackup access to a NAS (NDMP) host
- About access for three-way backups and remote NDMP
- About Media and Device Management configuration
- Using the Device Configuration Wizard to configure an NDMP filer
- About adding volumes
- About verifying NDMP password and robot connection
- Adding NDMP storage units
- About creating an NDMP policy
- About environment variables in the backup selections list
- About appropriate host selection for NetApp cDOT backup policies
- About backup types in a schedule for an NDMP policy
- About enabling or disabling DAR
- Configuring NetBackup for NDMP in a clustered environment
- Configuring NDMP backup to NetBackup media servers (remote NDMP)
- Configuring NDMP DirectCopy
- Accelerator for NDMP
- Remote NDMP and disk devices
- Using the Shared Storage Option (SSO) with NetBackup for NDMP
- Backup and restore procedures
- Troubleshooting
- Using NetBackup for NDMP scripts
- About the NetBackup for NDMP scripts
- ndmp_start_notify script (UNIX)
- ndmp_start_notify.cmd script (Microsoft Windows)
- ndmp_end_notify script (UNIX)
- ndmp_end_notify.cmd script (Microsoft Windows)
- ndmp_start_path_notify script (UNIX)
- ndmp_start_path_notify.cmd script (Microsoft Windows)
- ndmp_end_path_notify script (UNIX)
- ndmp_end_path_notify.cmd script (Microsoft Windows)
- ndmp_moving_path_notify script (UNIX)
- ndmp_moving_path_notify.cmd script (Microsoft Windows)
- Introduction to NetBackup for NDMP
Using NDMP DirectCopy to duplicate a backup image
NetBackup uses NDMP DirectCopy when you duplicate a backup image. To run a duplication, you can use any of the following methods:
Initiate the duplication from the NetBackup Administration Console.
In the NetBackup Administration Console, select and then, in the right pane, in the list box select the action.
NetBackup Vault
Refer to the NetBackup Vault Administrator's Guide for more information.
The bpduplicate command
Refer to the NetBackup Commands Guide for detailed information about this command.
A storage lifecycle policy (SLP)
In the NetBackup Administration Console, select .
Refer to the NetBackup Administrator's Guide, Volume I for more information about SLPs.
If you use a NetApp cDOT system in SVM-scoped NDMP mode, NetBackup tries to match the affinity for the source and the destination tape drive path, if possible, so the duplication can be performed optimally.