NetBackup™ NAS Administrator's Guide
- Section I. About NAS backups
- Section II. Using NAS-Data-Protection (D-NAS)
- D-NAS overview
- Pre-requisites for D-NAS configuration
- Configure D-NAS policy for NAS volumes
- Using accelerator
- Replication using D-NAS policy
- Restoring from D-NAS backups
- Troubleshooting
- Troubleshooting
- Setting the log level
- Logging directories for Linux platforms
- Logging folders for Windows platforms
- Restore from a snapshot fails with status 133
- Backup from snapshot fails with error 50
- Backup from snapshot parent job fails with error 4213: Snapshot import failed
- Backup host pool creation fails with the error "Failed to fetch host list"
- Snapshot job fails and the snapshot command does not recognize the volume name
- Accelerator enabled incremental backup of NetApp NAS volume
- Snapshot method: Auto
- Section III. Section 3
- Introduction to NetBackup for NDMP
- About NetBackup for NDMP
- About Network Data Management Protocol (NDMP)
- Types of NDMP backup
- About NDMP policies in NetBackup
- About NetBackup storage units
- About assigning tape drives to different hosts
- About the NDMP backup process
- About the NDMP restore process
- About Direct Access Recovery (DAR)
- Snapshot Client assistance
- About NDMP multiplexing
- About NDMP support for Replication Director
- Limitations of Replication Director with NDMP
- About NDMP support for NetApp clustered Data ONTAP (cDOT)
- Installation Notes for NetBackup for NDMP
- Configuring NDMP backup to NDMP-attached devices
- About configuring NDMP-attached devices
- Authorizing NetBackup access to a NAS (NDMP) host
- About access for three-way backups and remote NDMP
- About Media and Device Management configuration
- Using the Device Configuration Wizard to configure an NDMP filer
- About adding volumes
- About verifying NDMP password and robot connection
- Adding NDMP storage units
- About creating an NDMP policy
- About environment variables in the backup selections list
- About appropriate host selection for NetApp cDOT backup policies
- About backup types in a schedule for an NDMP policy
- About enabling or disabling DAR
- Configuring NetBackup for NDMP in a clustered environment
- Configuring NDMP backup to NetBackup media servers (remote NDMP)
- Configuring NDMP DirectCopy
- Accelerator for NDMP
- Remote NDMP and disk devices
- Using the Shared Storage Option (SSO) with NetBackup for NDMP
- Backup and restore procedures
- Troubleshooting
- Using NetBackup for NDMP scripts
- About the NetBackup for NDMP scripts
- ndmp_start_notify script (UNIX)
- ndmp_start_notify.cmd script (Microsoft Windows)
- ndmp_end_notify script (UNIX)
- ndmp_end_notify.cmd script (Microsoft Windows)
- ndmp_start_path_notify script (UNIX)
- ndmp_start_path_notify.cmd script (Microsoft Windows)
- ndmp_end_path_notify script (UNIX)
- ndmp_end_path_notify.cmd script (Microsoft Windows)
- ndmp_moving_path_notify script (UNIX)
- ndmp_moving_path_notify.cmd script (Microsoft Windows)
- Introduction to NetBackup for NDMP
Replication using D-NAS policy
Using the NetBackup™ Snapshot Manager for Data Center you can replicate the hardware snapshots of NFS and SMB shares. The replicated snapshots are accessed on backup hosts and read by dynamic streams to create point in time backup copies. The following procedure describes how to configure a NAS-Data-Protection policy to use hardware snapshots and replication of NAS volumes.
Note:
For all the supported NAS storage arrays for replication, refer to the NetBackup Snapshot Manager section, under Snapshot Solutions in the NetBackup Hardware and Cloud Storage Compatibility List (HCL).
Table: Configuration steps
Step | Description | Reference topic |
|---|---|---|
1 | Configure the NetBackup Snapshot Manager server in NetBackup | For more details, refer the Installation and Upgrade chapter of the NetBackup™ Snapshot Manager for Data Center Administrator's Guide. |
2 | Configure the NAS storage array plug-in | For more details, see the Configure NetBackup snapshot manager storage array plug-ins chapter of the NetBackup™ Snapshot Manager for Data Center Administrator's Guide. |
3 | Add the backup hosts to a backup host pool. The backup hosts are responsible for data streaming. | |
4 | Configure the SLP to use snapshot and replication | For more details about replication, refer these chapters in the NetBackup™ Snapshot Manager for Data Center Administrator's Guide:
|
5 | Configure a NAS-Data-Protection policy to perform the operations that are specified in the SLP |