NetBackup™ SAN クライアントおよびファイバートランスポートガイド

Linux でファイバートランスポートサービスを設定するには

1. nbftsrv_config スクリプトを実行します。次に例を示します。ご使用のシステムでの出力は異なる場合があります。

   /usr/openv/netbackup/bin/admincmd/nbftsrv_config -scst -install
   Checking for SCST drivers and firmwares in the package. [yes]
   Checking if the server is not NetBackup Appliance. [yes]
   Checking for kernel version 3.10.0-1160. [yes]
   Checking for QLE2692 QLogic 16/32Gb HBA cards on the server. [yes]
   Checking for LPe31002 Emulex 16/32Gb HBA cards on the server. [yes]
   
   DISCLAIMER:
   -----------
   NOTE:
   1. When you install the SAN client with 16Gb HBA, the script stops the original qla2xxx and lpfc driver and updates the firmware ql2500_fw.bin. Only QLE2562/QLE2692 and emulex 16Gb HBA models are supported by this NetBackup version.
   2. Ensure that there is no other process that uses the HBAs. If there is an active process that uses qla2xxx or lpfc, manually restart the process after the installation completes.
   3. If you use the SANsurfer agent during the deployment of the environment, the script stops and restarts the SANsurfer agent daemon (qlremote).
   4. Stop all the backup jobs that use the FT user interface.
   
   
   Do you acknowledge this disclaimer? [y,n] (n) y
   

2. このセッションで HBA ポートが検出されるように、QLogic ドライバが再ロードされます。

   Proceeding to deploy SCST environment  [ok]
   
   Reload driver qla2xxx
   Removing qla2xxx.
   Successfully unloaded driver qla2xxx
   Load driver qla2xxx
   
   HBA-Type   Port WWN                Status   Supported Speeds               Current Speed
   QLE2562    21:00:00:24:ff:3e:f2:e9 Online   1 Gbit, 2 Gbit, 4 Gbit, 8 Gbit 8 Gbit
   QLE2692    21:00:f4:e9:d4:53:fc:14 Online   4 Gbit, 8 Gbit, 16 Gbit        8 Gbit
   QLE2692    21:00:f4:e9:d4:53:fc:15 Linkdown 4 Gbit, 8 Gbit, 16 Gbit        unknown
   LPe31002   10:00:00:10:9b:1d:4c:6a Online   4 Gbit, 8 Gbit, 16 Gbit        16 Gbit
   LPe31002   10:00:00:10:9b:1d:4c:6b Online   4 Gbit, 8 Gbit, 16 Gbit        16 Gbit
   QLE2562    21:00:00:24:ff:3e:f2:e8 Linkdown 1 Gbit, 2 Gbit, 4 Gbit, 8 Gbit unknown
   
   NOTE:
   The types of HBA cards listed are QLE2692/QLE2562 or Emulex LPE31002. Some of the WWNs may be used to connect to an external storage and other external devices.
   
   Do you want to continue? [y,n] (n) y

3. ポート番号を入力し、このセッション中の操作の警告を確認します。

   Please input the Port WWNs you want to use as the targets (separated by commas like: wwn1,wwn2...):10:00:00:10:9b:1d:4c:6a,10:00:00:10:9b:1d:4c:6b
   The input is: 10:00:00:10:9b:1d:4c:6a,10:00:00:10:9b:1d:4c:6b
   The targets you defined are Emulex HBAs
   The targets you defined: 10:00:00:10:9b:1d:4c:6a 10:00:00:10:9b:1d:4c:6b
   Do you want to redefine the targets? [y,n] (n) n
   Do you want to add additional targets? [y,n] (n) n
   The targets you defined: 10:00:00:10:9b:1d:4c:6a 10:00:00:10:9b:1d:4c:6b
   The targets you have defined contain 16Gb HBA cards.
   
   NOTE:
   1. Make sure that you do not use a WWN that is used to connect to external storage.
   2. Make sure to define the input WWNs as targets.
   3. Make sure the WWNs can be zoned with WWNs of clients.
   Do you want to continue to setup the WWNs as targets? [y,n] (n) y

4. FTMS 環境が配備されます。

   --------------------------------------------
   FTMS environment installation started.
   --------------------------------------------
   Successfully created the dependent path: /var/lib/scst/pr.
   Successfully created the dependent path: /var/lib/scst/vdev_mode_pages.
   Successfully copied /usr/openv/netbackup/bin/driver/lancerg6_A12.8.340.8.grp to /lib/firmware/LPE31004.grp.
   Successfully copied /usr/openv/netbackup/bin/driver/scst/ocs_fc_scst.ko.3.10.0-1160.el7.x86_64 to /lib/modules/3.10.0-1160.15.2.el7.x86_64/extra/ocs_fc_scst.ko.
   Successfully copied /usr/openv/netbackup/bin/driver/scst/scst.ko.3.10.0-1160.el7.x86_64 to /lib/modules/3.10.0-1160.15.2.el7.x86_64/extra/scst.ko.
   Successfully copied /usr/openv/netbackup/bin/driver/scst/scst_user.ko.3.10.0-1160.el7.x86_64 to /lib/modules/3.10.0-1160.15.2.el7.x86_64/extra/scst_user.ko.
   Successfully created /etc/modprobe.d/ocs_fc_scst.conf.
   Successfully copied /usr/openv/netbackup/bin/nbftsrvr to /usr/openv/netbackup/bin/nbftsrvr_old.
   Successfully copied /usr/openv/netbackup/bin/goodies/nbftserver_scst to /etc/rc.d/init.d/nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc2.d/S21nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc3.d/S21nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc5.d/S21nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc0.d/K03nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc1.d/K03nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc6.d/K03nbftserver.
   Successfully enabled nbftserver.
   Successfully created /etc/modules-load.d/scst.conf.
   Successfully find PCIID:0000:07:00.0 for target:10:00:00:10:9b:1d:4c:6a
   Successfully find PCIID:0000:07:00.1 for target:10:00:00:10:9b:1d:4c:6b
   Successfully bind target mode for pciid: 0000:07:00.0.
   Successfully bind target mode for pciid: 0000:07:00.1.
   Successfully rebind emulex target ports.
   Successfully modify the attribute of /sys/kernel/scst_tgt/targets/ocs_xe201/10:00:00:10:9b:1d:4c:6a/enabled with value 1.
   Successfully write /sys/class/fc_host/host13/issue_lip with value 1
   Enable target: 10:00:00:10:9b:1d:4c:6a
   Successfully modify the attribute of /sys/kernel/scst_tgt/targets/ocs_xe201/10:00:00:10:9b:1d:4c:6b/enabled with value 1.
   Successfully write /sys/class/fc_host/host14/issue_lip with value 1
   Enable target: 10:00:00:10:9b:1d:4c:6b
   Previous initramfs image is saved at /boot/initramfs-3.10.0-1160.15.2.el7.x86_64.img.03-19-21.19:31:51.
   Running dracut, it may take several minutes to complete...
   /sbin/dracut succeeded
   Successfully moved /boot/initramfs-3.10.0-1160.15.2.el7.x86_64.img.tmp to /boot/initramfs-3.10.0-1160.15.2.el7.x86_64.img
   NetBackup Fibre Transport Server started.
   -------------------------------
   Driver ocs_fc_scst is loaded
   -------------------------------
   Driver scst is loaded
   -------------------------------
   Driver scst_user is loaded
   
   --------------------------------------------
   FTMS environment installation completed.
   --------------------------------------------