Storage Foundation and High Availability 8.0.2 設定およびアップグレードガイド - Linux

非 SCSI-3 フェンシングのサンプル /etc/vxfenmode ファイル

#
# vxfen_mode determines in what mode VCS I/O Fencing should work.
#
# available options:
# scsi3      - use scsi3 persistent reservation disks
# customized - use script based customized fencing
# disabled   - run the driver but don't do any actual fencing
#
vxfen_mode=customized

# vxfen_mechanism determines the mechanism for customized I/O 
# fencing that should be used.
# 
# available options:
# cps      - use a coordination point server with optional script
#            controlled scsi3 disks
#
vxfen_mechanism=cps

#
# scsi3_disk_policy determines the way in which I/O fencing
# communicates with the coordination disks. This field is
# required only if customized coordinator disks are being used.
#
# available options:
# dmp - use dynamic multipathing
#
scsi3_disk_policy=dmp

# 
# Seconds for which the winning sub cluster waits to allow for the
# losing subcluster to panic & drain I/Os. Useful in the absence of
# SCSI3 based data disk fencing loser_exit_delay=55
#
# Seconds for which vxfend process wait for a customized fencing
# script to complete. Only used with vxfen_mode=customized
# vxfen_script_timeout=25

#
# vxfen_honor_cp_order determines the order in which vxfen 
# should use the coordination points specified in this file.
#
# available options:
# 0	- vxfen uses a sorted list of coordination points specified
# in this file, the order in which coordination points are specified
# does not matter.
#	  (default)
# 1	- vxfen uses the coordination points in the same order they are
# 	  specified in this file

# Specify 3 or more odd number of coordination points in this file, 
# each one in its own line. They can be all-CP servers, all-SCSI-3 
# compliant coordinator disks, or a combination of CP servers and 
# SCSI-3 compliant coordinator disks.
# Please ensure that the CP server coordination points are 
# numbered sequentially and in the same order on all the cluster
# nodes.
#
# Coordination Point Server(CPS) is specified as follows:
#
# 	cps<number>=[<vip/vhn>]:<port>
#
# If a CPS supports multiple virtual IPs or virtual hostnames
# over different subnets, all of the IPs/names can be specified
# in a comma separated list as follows:
#
#	cps<number>=[<vip_1/vhn_1>]:<port_1>,[<vip_2/vhn_2>]:<port_2>,
# ...,[<vip_n/vhn_n>]:<port_n>
#
# Where,
#	<number>
#		is the serial number of the CPS as a coordination point; must
#		start with 1.
#	<vip>
#		is the virtual IP address of the CPS, must be specified in
#		square brackets ("[]").
#	<vhn>
#		is the virtual hostname of the CPS, must be specified in square
#		brackets ("[]").
#	<port>
#		is the port number bound to a particular <vip/vhn> of the CPS.
#		It is optional to specify a <port>. However, if specified, it
#		must follow a colon (":") after <vip/vhn>. If not specified, the
#		colon (":") must not exist after <vip/vhn>.
#
# For all the <vip/vhn>s which do not have a specified <port>,
# a default port can be specified as follows:
#
#	port=<default_port>
#
# 	Where <default_port> is applicable to all the <vip/vhn>s for which a
# 	<port> is not specified. In other words, specifying <port> with a
# 	<vip/vhn> overrides the <default_port> for that <vip/vhn>.
#	If the <default_port> is not specified, and there are <vip/vhn>s for
#	which <port> is not specified, then port number 14250 will be used
#	for such <vip/vhn>s.
#
# Example of specifying CP Servers to be used as coordination points:
#	port=57777
#	cps1=[192.168.0.23],[192.168.0.24]:58888,[cps1.company.com]
# 	cps2=[192.168.0.25]
#	cps3=[cps2.company.com]:59999
#
#	In the above example,
#	- port 58888 will be used for vip [192.168.0.24]
#	- port 59999 will be used for vhn [cps2.company.com], and
#	- default port 57777 will be used for all remaining <vip/vhn>s:
#	   [192.168.0.23]
#	   [cps1.company.com]
#	   [192.168.0.25]
#	- if default port 57777 were not specified, port 14250 would be
#  used for all remaining <vip/vhn>s:
#	   [192.168.0.23]
#	   [cps1.company.com]
#	   [192.168.0.25]
#
# SCSI-3 compliant coordinator disks are specified as:
#	  
# 	vxfendg=<coordinator disk group name>
#	Example:
#		vxfendg=vxfencoorddg
#
# Examples of different configurations:
# 	1. All CP server coordination points
#	cps1=
#	cps2=
#	cps3=
#
#	2. A combination of CP server and a disk group having two SCSI-3 
#	coordinator disks 
#	cps1=
#	vxfendg=
#	Note: The disk group specified in this case should have two disks
#
#	3. All SCSI-3 coordinator disks
#	vxfendg=
#	Note: The disk group specified in case should have three disks 
# cps1=[cps1.company.com]
# cps2=[cps2.company.com]
# cps3=[cps3.company.com]
# port=443