Search <book_title>...

Veritas NetBackup™ Deduplication Guide

Last Published: 2021-01-06

Product(s): NetBackup (9.0.0.1, 9.0)

About seeding the MSDP fingerprint cache for remote client deduplication

Veritas provides a method for seeding the fingerprint cache for a new client. The use case that benefits the most from seeding is the first backup of a remote client over a high latency network such as a WAN. The performance of the first backup is then similar to the performance of an existing client.

An important consideration is the client from which to seed the cache. When you choose a similar client, consider the following:

If most of the information is the operating system files, use any client with the same operating system.
If most of the information is data, finding a client with the same data may be unlikely. Therefore, consider physically moving a copy of the data to the datacenter. Back up that data on a similar client, and then use that client and policy for the seed.
The more similar the clients are, the greater the cache hit rate is.

Two methods exist to configure cache seeding. You can use either method. The following table describes the seeding configuration methods.

Table: Seeding configuration methods

Host on which to configure seeding	Description
On the client	Configure seeding on the client for one or only a few clients. See Configuring MSDP fingerprint cache seeding on the client.
On the storage server	The use case that benefits the most is many clients to seed, and they can use the fingerprint cache from a single host. See Configuring MSDP fingerprint cache seeding on the storage server.

Host on which to configure seeding

Description

On the client

Configure seeding on the client for one or only a few clients.

See Configuring MSDP fingerprint cache seeding on the client.

On the storage server

The use case that benefits the most is many clients to seed, and they can use the fingerprint cache from a single host.

See Configuring MSDP fingerprint cache seeding on the storage server.

To ensure that NetBackup uses the seeded backup images, the first backup of a client after you configure seeding must be a full backup with a single stream. Specifically, the following two conditions must be met in the backup policy:

The Attributes tab Allow multiple data streams attribute must be unchecked.
The backup selection cannot include anyNEW_STREAM directives.

If these two conditions are not met, NetBackup may use multiple streams. If the Attributes tab Limit jobs per policy is set to a number less than the total number of streams, only those streams use the seeded images to populate the cache. Any streams that are greater than the Limit jobs per policy value do not benefit from seeding, and their cache hit rates may be close to 0%.

After the first backup, you can restore the original backup policy parameter settings.

The following items are example of informational messages that show that seeding occurred:

Activity Monitor Job Details

1/2/2015 2:18:23 AM - Info nbmaster1(pid=6340) StorageServer=PureDisk:nbmaster1; Report=PDDO Stats for (nbmaster1): scanned: 3762443 KB, CR sent: 1022 KB, CR sent over FC: 0 KB, dedup: 100.0%, cache hits: 34364 (100.0%)

1/2/2015 2:18:24 AM - Info nbmaster1(pid=6340) StorageServer=PureDisk:nbmaster1; Report=PDDO Stats for (nbmaster1): scanned: 1 KB, CR sent: 0 KB, CR sent over FC: 0 KB, dedup: 100.0%

Deduplication plug-in log (pdplugin.log) on the client

01/02/15 02:15:17 [4452] [4884] [DEBUG] PDSTS: cache_util_get_cache_dir: enter db=/nbmaster1#1/2, scp='', bc=opscenter1, bp=seedfinal, bl=4096

01/02/15 02:15:17 [4452] [4884] [DEBUG] PDSTS: cache_util_get_cache_dir: new backup, using existing client seeding directory

01/02/15 02:15:17 [4452] [4884] [DEBUG] PDSTS: cache_util_get_cache_dir: exit db=/nbmaster1#1/2, scp='', bc=opscenter1, bp=seedfinal, bl=4096, cachedir_buf='/nbmaster1#1/2/#pdseed/opscenter1' err=0

See NetBackup MSDP log files.

Deduplication proxy server log (nbostpxy.log) on the client

02:15:17.417[4452.4884][DEBUG][dummy][11:bptm:6340:nbmaster1][DEBUG] PDSTS: cache_util_get_cache_dir: enter db=/nbmaster1#1/2, scp='', bc=opscenter1, bp=seedfinal, bl=4096

02:15:17.433[4452.4884][DEBUG][dummy][11:bptm:6340:nbmaster1][DEBUG] PDSTS: cache_util_load_fp_cache_nbu: enter dir_path=/nbmaster1#1/2/#pdseed/opscenter1, t=16s, me=1024

02:15:17.449[4452.4884][DEBUG][dummy][11:bptm:6340:nbmaster1][DEBUG] PDSTS: cache_util_load_fp_cache_nbu: adding 'nbmaster1_1420181254_C1_F1.img' to cache list (1)

02:15:17.449[4452.4884][DEBUG][dummy][11:bptm:6340:nbmaster1][DEBUG] PDSTS: cache_util_load_fp_cache_nbu: opening /nbmaster1#1/2/#pdseed/opscenter1/nbmaster1_1420181254_C1_F1.img for image cache (1/1)

02:15:29.585[4452.4884][DEBUG][dummy][11:bptm:6340:nbmaster1][DEBUG] PDVFS: pdvfs_lib_log: soRead: segment c32b0756d491871c45c71f811fbd73af already present in cache.

02:15:29.601[4452.4884][DEBUG][dummy][11:bptm:6340:nbmaster1][DEBUG] PDVFS: pdvfs_lib_log: soRead: segment 346596a699bd5f0ba5389d4335bc7429 already present in cache.

See NetBackup MSDP log files.

For more information about seeding, see the following Veritas tech note:

http://www.veritas.com/docs/TECH144437

See About the MSDP fingerprint cache.