Search <book_title>...

Veritas Access Appliance Administrator's Guide

Last Published: 2022-12-07

Product(s): Appliances (7.4.3)

Platform: Veritas 3340,Access Appliance OS

Addition of multiple file systems to a Replicated Volume Group

Access Appliance supports the addition of multiple file systems to a Replicated Volume Group (RVG). You can enable replication for many file systems in a single RVG.

To configure an RVG with multiple file systems

Create an RVG. You can specify the name in the parameter.

replication> continuous enable fs_name pool_name link_name 
[delayed=yes|no] rvg_name

fs_name	Specifies the name of the file system. It should be present on the source cluster.
pool_name	Specifies the pool name. It should be present on the source as well as target cluster.
link_name	Specifies the link name. This link is created during authentication of the source and the target cluster,
[delayed=yes\|delayed=no]	Specifies if the continuous replication should happen in delayed mode, This is an optional parameter and the default value is 'no'.
rvg_name	Specifies the name of the RVG.
create_target_fs	The value is `yes` if you want to create file system on secondary cluster. Else, the value is set to `no`.
srl_size	Specify the SRL size for the filesystem. .

For example: To create an RVG, rvg_test:

replication> continuous enable fs1 pool1 src_link delayed=yes rvg_test

You can specify the RVG name in the command. If the RVG name is not specified, the RVG is created with the default name. The default name of the RVG is rvg_fs_name.

Before adding another file system, ensure that the data is synced between the primary and secondary sites and the second filesystem is offline.
```
replication> continuous status fs_name
```
Add another file system to the same RVG.
```
replication> continuous enable fs_name pool_name link_name 
[delayed=yes|no] rvg_name
```
Note:
If you have configured any CIFS shares on the file system, you must remove them before you add the file system to an existing RVG.
For example: To add a file system. fs2 to the existing RVG, rvg_test:
```
replication> continuous enable fs2 pool1 src_link delayed=yes rvg_test
```
After the execution of this command, rvg_test is created with two file systems in it, fs1 and fs2.
You can add more file systems in the RVG by repeating steps 2 to 3.

You can view the mapping between the RVG and the file systems using the following command:

replication> continuous show
RVG                    FS List
------                 ---------------
rvg_test               fs1,fs2

The replication continuous commands such as start, stop, pause, resume, failover, and failback accept the file system name as the parameter, but the changes are applicable for the entire RVG (including all the file systems which are part of the RVG).

For example, if you have multiple file systems in a RVG and if you failover using the replication continuous failover fs1 command, then the entire RVG will failover.

The replication continuous disable command does not delete the RVG until the file system is the last file system in the RVG.

For each file system that is added to the RVG, if the file system is configured in async mode, the Storage Replicator Log (SRL) grows by 20% of the file system size, and if the file system is configured in sync mode, it grows by 5% of the file system size. If the SRL has been grown more than 12 times(either as a result of the fs grow command or addition of file systems to the RVG), then the SRL will not be grown further.

Note:

If a file system was created before you performed an upgrade to Access Appliance 7.4.3, contact Veritas Technical Support to add the file system to an existing RVG or to create a new RVG with the file system.