Dynamic Multi-Pathing 8.0.1 Administrator's Guide - Windows

Last Published:
Product(s): InfoScale & Storage Foundation (8.0.1)
Platform: Windows
  1. Understanding DMPW
    1.  
      DMP overview
    2.  
      Major features of Dynamic Multi-Pathing
    3. How DMP works
      1. How DMP monitors I/O on paths
        1.  
          Path failover mechanism
      2.  
        Load balancing
      3.  
        DMP in a clustered environment
    4.  
      Multiple paths to disk arrays
    5.  
      Device discovery
  2. Setting up DMPW
    1.  
      Active/Active and Active/Passive settings
    2. Active/Active and Active/Passive settings in a cluster environment
      1.  
        DMP DSMs
      2.  
        SCSI-3 PGR technology
      3.  
        Enabling SCSI-3 PGR
    3. Add and remove paths
      1.  
        Adding a path
      2.  
        Removing a path
    4. Specify load balancing settings and the primary path
      1.  
        Specifying load balancing settings for an array
      2.  
        Specifying load balancing settings for a disk
      3.  
        Specifying the primary path for an array or disk
    5. Configuring DSMs without storage connection
      1.  
        Specify DSM settings without storage connection
  3. Administering DMPW
    1.  
      About administering DMP
    2. DMP DSMs menus
      1.  
        Displaying the menu for arrays
      2.  
        Commands for arrays
      3.  
        Displaying the menu for disks
      4.  
        Commands for paths of a disk
      5.  
        Statistics monitoring
      6.  
        Clear performance statistics
      7.  
        Device settings
      8.  
        Set primary path
      9.  
        Properties
    3. View array, disk, and path status
      1.  
        Array status
      2.  
        Device status
      3.  
        Path status
    4. vxdmpadm
      1.  
        vxdmpadm dsminfo
      2.  
        vxdmpadm arrayinfo
      3.  
        vxdmpadm deviceinfo
      4.  
        vxdmpadm pathinfo
      5.  
        vxdmpadm arrayperf
      6.  
        vxdmpadm deviceperf
      7.  
        vxdmpadm pathperf
      8.  
        vxdmpadm allperf
      9.  
        vxdmpadm iostat
      10.  
        vxdmpadm cleardeviceperf
      11.  
        vxdmpadm cleararrayperf
      12.  
        vxdmpadm clearallperf
      13.  
        vxdmpadm setdsmscsi3
      14.  
        vxdmpadm setarrayscsi3
      15.  
        vxdmpadm setattr dsm
      16.  
        vxdmpadm setattr array
      17.  
        vxdmpadm setattr device
      18.  
        vxdmpadm setattr path
      19.  
        vxdmpadm set isislog
      20.  
        vxdmpadm rescan
      21.  
        vxdmpadm disk list
      22.  
        vxdmpadm getdsmattrib
      23.  
        vxdmpadm getmpioparam
      24.  
        vxdmpadm setmpioparam
  4. Performance tuning
    1.  
      Specifying control timer settings for an array
  5. Troubleshooting
    1. Resolving DMP issues
      1.  
        When a DMP license is no longer valid
      2.  
        When an unknown disk group appears in a DMP environment
    2. Using status information
      1.  
        Path status
      2.  
        Path states
  6. Glossary
    1.  
      Dynamic Multi-Pathing glossary

Specify load balancing settings and the primary path

The primary path setting is only available when you select the Fail Over Only (Active/Passive) load balancing setting for an array or disk.

When you first set up an array under DMP DSMs, you must make sure that you have the load balancing setting you want for the paths in the array. After that is done, all of the disks in the array by default have the same load balancing setting. Then, if desired, you can change this setting for individual disks. The load balancing settings are located in the Load Balance Policy section of the Array Settings wizard and the Device Settings screen.

All of the load balancing settings, except for Fail Over Only (Active/Passive), enable load balancing among the active paths. The Fail Over Only (Active/Passive) setting does not provide load balancing because data transfer only occurs on the one active path, the primary path.

Note:

The type of array or disk determines which load balancing settings are available. Load balance settings that are not supported are grayed-out in the VEA GUI. Refer to the documentation for your array or disk for more information about supported load balance settings.

This section gives the step-by-step directions for specifying the load balancing settings for the paths in an array and for individual disks.

See Specifying load balancing settings for an array.

See Specifying load balancing settings for a disk.

See Specifying the primary path for an array or disk.

More Information

Active/Active and Active/Passive settings