NetBackup™ for NDMP Administrator's Guide
- Introduction to NetBackup for NDMP
- About NetBackup for NDMP
- About Network Data Management Protocol (NDMP)
- Types of NDMP backup
- About NDMP policies in NetBackup
- About NetBackup storage units
- About assigning tape drives to different hosts
- About the NDMP backup process
- About the NDMP restore process
- About Direct Access Recovery (DAR)
- Snapshot Client assistance
- About NDMP multiplexing
- About NDMP support for Replication Director
- Limitations of Replication Director with NDMP
- About NDMP support for NetApp clustered Data ONTAP (cDOT)
- Installation Notes for NetBackup for NDMP
- Configuring NDMP backup to NDMP-attached devices
- About configuring NDMP-attached devices
- Authorizing NetBackup access to a NAS (NDMP) host
- About access for three-way backups and remote NDMP
- About Media and Device Management configuration
- Using the Device Configuration Wizard to configure an NDMP filer
- About adding volumes
- About verifying NDMP password and robot connection
- Adding NDMP storage units
- About creating an NDMP policy
- Attributes tab options for an NDMP policy
- Schedules tab options for an NDMP policy with Accelerator for NDMP enabled
- Clients tab options for an NDMP policy
- Backup selection options for an NDMP policy
- About environment variables in the backup selections list
- About appropriate host selection for NetApp cDOT backup policies
- About backup types in a schedule for an NDMP policy
- About enabling or disabling DAR
- Configuring NetBackup for NDMP in a clustered environment
- Configuring NDMP backup to NetBackup media servers (remote NDMP)
- Configuring NDMP DirectCopy
- Accelerator for NDMP
- Remote NDMP and disk devices
- Using the Shared Storage Option (SSO)
- Backup and restore procedures
- Troubleshooting
- Using NetBackup for NDMP scripts
- About the NetBackup for NDMP scripts
- ndmp_start_notify script (UNIX)
- ndmp_start_notify.cmd script (Microsoft Windows)
- ndmp_end_notify script (UNIX)
- ndmp_end_notify.cmd script (Microsoft Windows)
- ndmp_start_path_notify script (UNIX)
- ndmp_start_path_notify.cmd script (Microsoft Windows)
- ndmp_end_path_notify script (UNIX)
- ndmp_end_path_notify.cmd script (Microsoft Windows)
- ndmp_moving_path_notify script (UNIX)
- ndmp_moving_path_notify.cmd script (Microsoft Windows)
NDMP backup levels
At the start of a debug log, you may see an entry titled LEVEL. This entry refers to an environment variable that NetBackup set based on the type of backup. Here is an example from a bptm log:
08:48:38.816 [22923] <2> write_data_ndmp: backup environment
values:
08:48:38.816 [22923] <2> write_data_ndmp: Environment 1:
TYPE=dump
08:48:38.816 [22923] <2> write_data_ndmp: Environment 2:
FILESYSTEM=/vol/vol0/2million
08:48:38.817 [22923] <2> write_data_ndmp: Environment 3:
PREFIX=/vol/vol0/2million
08:48:38.817 [22923] <2> write_data_ndmp: Environment 4: LEVEL=0The NDMP backup level is modeled after UNIX dump levels. The backup level is a number in the range of 0 to 9.
An NDMP backup level of 0 is a full backup. A backup level greater than 0 is an incremental backup of all objects that were modified since the last backup of a lower level. For example, level 1 is a backup of all objects that were modified since the full backup (level 0). Level 3 is a backup of all objects that were modified since the last level 2 incremental.
Table: NetBackup backup types and corresponding NDMP backup levels
NetBackup backup types | NDMP backup levels |
|---|---|
NetBackup Full | NDMP level 0 |
NetBackup Cumulative Incremental | NDMP level 1 |
NetBackup Differential Incremental | NDMP level (last level + 1, up to 9) Some vendors support level values that are greater than 9. For valid level values for your device, see the NetBackup for NDMP: NAS Appliance Information from the Veritas Support website: |
More information is available on environment variables.
More Information