Important Update: Cohesity Products Documentation

All Cohesity product documentation are now managed via the Cohesity Docs Portal: https://docs.cohesity.com/HomePage/Content/home.htm. Some documentation available here may not reflect the latest information or may no longer be accessible.

NetBackup™ Flex Scale Installation and Configuration Guide

Last Published:
Product(s): Appliances (3.5)
Platform: NetBackup Flex Scale OS
  1. Preparing for NetBackup Flex Scale deployment
    1.  
      Deployment overview
    2.  
      Deployment options
  2. Configuring NetBackup Flex Scale
    1. Assigning public IP address to a management network interface
      1.  
        Assigning a public IP address to network adapter eth1 or to a VLAN on eth1 of a node
      2.  
        Configuring a bond device and assigning an IP address to the bonded device or to a VLAN on the bonded device
    2.  
      NetBackup Flex Scale configuration methods
    3.  
      Configuring NetBackup Flex Scale using the setup wizard
    4.  
      YML configuration file
  3. Upgrading NetBackup Flex Scale to 3.5
    1.  
      About NetBackup Flex Scale upgrades and EEBs
    2.  
      NetBackup Flex Scale upgrade overview
    3.  
      Supported upgrade paths
    4. Performing pre-upgrade tasks
      1.  
        Considerations for upgrade when disaster recovery is configured
    5.  
      Downloading the upgrade file
    6.  
      Uploading the upgrade file and performing an upgrade precheck
    7.  
      Performing an upgrade using GUI
    8. Performing post-upgrade tasks
      1.  
        Downloading and installing the required EEBs
      2.  
        Verifying appliance firmware compatibility
      3.  
        Adding NetBackup license file
      4.  
        Saving the default password of the HPE iLO Administrator user
      5.  
        Collecting logs post upgrade
    9.  
      Collecting logs for an upgrade precheck failure
  4. Upgrading the firmware in NetBackup Flex Scale cluster
    1.  
      About firmware upgrades
    2.  
      Determining if a firmware upgrade is required
    3.  
      Downloading the firmware package
    4.  
      About the firmware upgrade options
    5. Upgrading the firmware
      1. Updating the firmware in NetBackup Flex Scale clusters using HPE iLO
        1.  
          Upgrading the firmware using the rolling method
        2.  
          Upgrading the firmware using the parallel method
        3.  
          Updating the ACL file on the cluster nodes
  5. Managing EEBs
    1.  
      Downloading EEBs
    2.  
      Installing EEBs using GUI
    3.  
      Installing EEBs during upgrade
    4.  
      Removing EEBs using GUI
    5.  
      Uninstalling EEBs using GUI
    6.  
      Installing EEBs using REST APIs
  6. Removing NetBackup Flex Scale
    1. About disk erasure
      1.  
        Configuring data erasure
      2.  
        Viewing the data erasure status
      3.  
        Aborting data erasure
    2.  
      About NetBackup Flex Scale node factory reset
    3.  
      Performing a factory reset on a node
  7. Appendix A. Installing NetBackup Flex Scale using a downloaded ISO file
    1.  
      About NetBackup Flex Scale software installation
    2.  
      Enabling remote IPMI connections
    3.  
      Setting up the RAID configuration on the nodes
    4.  
      Configuring the BIOS settings on the nodes
    5.  
      Downloading the product installer ISO
    6.  
      Mounting the ISO file on the nodes
    7.  
      Installing NetBackup Flex Scale using the ISO
  8. Appendix B. Upgrading a NetBackup Flex Scale node
    1.  
      Upgrading a node that is not in a cluster

Uninstalling EEBs using GUI

You can uninstall EEBs from the GUI using the rolling or the parallel method. In the rolling method, EEBs are uninstalled on each node successively. In the parallel method, EEBs are uninstalled on all the nodes in parallel.

To uninstall an EEB using the GUI

  1. Go to Settings > Software management > Add-ons.
  2. On the Add-ons tab, select the EEBs that you want to uninstall and click Rollback.
  3. When prompted, select either the rolling or parallel option, then click Rollback.

    EEB uninstallation progress information is displayed at the top of the page. To monitor the progress, click View details. Once the EEBs are uninstalled, their status changes from Installed to Available.