Veritas NetBackup™ for HBase Administrator's Guide

Last Published:
Product(s): NetBackup (9.0.0.1, 9.0)
  1. Introduction
    1.  
      Protecting HBase data using NetBackup
    2.  
      Backing up HBase data
    3.  
      Restoring HBase data
    4.  
      NetBackup for HBase terminologies
    5.  
      Limitations
  2. Deploying HBase plug-in for NetBackup
    1.  
      About the HBase plug-in deployment
    2.  
      Pre-requisites for installing the HBase plug-in
    3.  
      Operating system and platform compatibility
    4.  
      License for HBase plug-in for NetBackup
    5.  
      Preparing the HBase cluster
    6.  
      Best practices for deploying the HBase plug-in
    7.  
      Post installation procedures
    8.  
      Verifying the deployment of the HBase plug-in
  3. Configuring NetBackup for HBase
    1.  
      About configuring NetBackup for HBase
    2. Managing backup hosts
      1.  
        Whitelisting a NetBackup client on NetBackup master server
      2.  
        Configure a NetBackup Appliance as a backup host
    3.  
      Adding HBase credentials in NetBackup
    4. Configuring the HBase plug-in using the HBase configuration file
      1.  
        Configuring NetBackup for a highly-available HBase cluster
      2.  
        Configuring communication between NetBackup and HBase clusters that have SSL enabled (HTTPS)
    5.  
      Configuration for a HBase cluster that uses Kerberos
    6. Configuring NetBackup policies for HBase plug-in
      1. Creating a BigData backup policy
        1. Creating BigData policy using the NetBackup Administration Console
          1.  
            Using the Policy Configuration Wizard to create a BigData policy for HBase clusters
          2.  
            Using the NetBackup Policies utility to create a BigData policy for HBase clusters
        2.  
          Using NetBackup Command Line Interface (CLI) to create a BigData policy for HBase clusters
    7.  
      Disaster recovery of a HBase cluster
  4. Performing backups and restores of HBase
    1. About backing up a HBase cluster
      1.  
        Pre-requisite for running backup and restore operations for a HBase cluster with Kerberos authentication
      2.  
        Backing up a HBase cluster
      3.  
        Best practices for backing up a HBase cluster
    2. About restoring a HBase cluster
      1. Restoring HBase data on the same HBase cluster
        1.  
          Using the Restore Wizard to restore HBase data on the same cluster
        2.  
          Using the bprestore command to restore HBase data on the same HBase cluster
    3.  
      Restoring HBase data on an alternate HBase cluster
    4.  
      Restoring truncated tables
    5.  
      Best practices for restoring a HBase cluster
  5. Troubleshooting
    1.  
      About NetBackup for HBase debug logging
    2.  
      Backup fails with error 6609
    3.  
      Backup fails with error 6601
    4.  
      Backup fails with error 6623
    5.  
      Restore fails with error 2850
    6.  
      Backup fails with error 20
    7.  
      Backup fails with error 112
    8.  
      Backup operation fails with error 6654
    9.  
      NetBackup configuration and certificate files do not persist after the container-based NetBackup appliance restarts
    10.  
      Configuration file is not recovered after a disaster recovery
  6.  
    Index

Creating BigData policy using the NetBackup Administration Console

If you prefer using the NetBackup Administration Console for creating BigData policy, you can use either of the following methods:

  • Creating a BigData policy using the Policy Configuration Wizard

  • Creating a BigData policy using the NetBackup Policies utility

The easiest method to set up a BigData policy is to use the Policy Configuration Wizard. This wizard guides you through the setup process by automatically choosing the best values for most configurations. Not all policy configuration options are presented through the wizard. For example, calendar-based scheduling and the Data Classification setting. After the policy is created, modify the policy in the Policies utility to configure the options that are not part of the wizard.