Veritas NetBackup™ for HBase Administrator's Guide

Last Published:
Product(s): NetBackup (8.2, 8.1.2)
Platform: Linux,UNIX,Windows
  1. Introduction
    1.  
      Protecting HBase data using NetBackup
    2.  
      Backing up HBase data
    3.  
      Restoring HBase data
    4.  
      NetBackup for HBase terminologies
    5.  
      Limitations
  2. Deploying HBase plug-in for NetBackup
    1.  
      About the HBase plug-in deployment
    2.  
      Pre-requisites for installing the HBase plug-in
    3.  
      Operating system and platform compatibility
    4.  
      License for HBase plug-in for NetBackup
    5.  
      Preparing the HBase cluster
    6.  
      Best practices for deploying the HBase plug-in
    7.  
      Post installation procedures
    8.  
      Verifying the deployment of the HBase plug-in
  3. Configuring NetBackup for HBase
    1.  
      About configuring NetBackup for HBase
    2. Managing backup hosts
      1.  
        Whitelisting a NetBackup client on NetBackup master server
      2.  
        Configure a NetBackup Appliance as a backup host
    3.  
      Adding HBase credentials in NetBackup
    4. Configuring the HBase plug-in using the HBase configuration file
      1.  
        Configuring NetBackup for a highly-available HBase cluster
    5.  
      Configuration for a HBase cluster that uses Kerberos
    6. Configuring NetBackup policies for HBase plug-in
      1. Creating a BigData backup policy
        1. Creating BigData policy using the NetBackup Administration Console
          1.  
            Using the Policy Configuration Wizard to create a BigData policy for HBase clusters
          2.  
            Using the NetBackup Policies utility to create a BigData policy for HBase clusters
        2.  
          Using NetBackup Command Line Interface (CLI) to create a BigData policy for HBase clusters
    7.  
      Disaster recovery of a HBase cluster
  4. Performing backups and restores of HBase
    1. About backing up a HBase cluster
      1.  
        Pre-requisite for running backup and restore operations for a HBase cluster with Kerberos authentication
      2.  
        Backing up a HBase cluster
      3.  
        Best practices for backing up a HBase cluster
    2. About restoring a HBase cluster
      1. Restoring HBase data on the same HBase cluster
        1.  
          Using the Restore Wizard to restore HBase data on the same cluster
        2.  
          Using the bprestore command to restore HBase data on the same HBase cluster
    3.  
      Restoring HBase data on an alternate HBase cluster
    4.  
      Restoring truncated tables
    5.  
      Best practices for restoring a HBase cluster
  5. Troubleshooting
    1.  
      About NetBackup for HBase debug logging
    2.  
      Backup fails with error 6609
    3.  
      Backup fails with error 6601
    4.  
      Backup fails with error 6623
    5.  
      Restore fails with error 2850
    6.  
      Backup fails with error 20
    7.  
      Backup fails with error 112

Disaster recovery of a HBase cluster

For disaster recovery of the HBase cluster, perform the following tasks:

Table: Performing disaster recovery

Task

Description

After the HBase cluster and nodes are up, prepare the cluster for operations with NetBackup.

Perform the following tasks:

Update firewall settings so that the backup hosts can communicate with the HBase cluster.

Ensure that webhbase service is enabled on the HBase cluster.

See Preparing the HBase cluster.

To establish a seamless communication between HBase clusters and NetBackup for successful backup and restore operations, you must add and update HBase credentials to NetBackup master server.

Use tpconfig command to add HBase credentials in NetBackup master server.

See Adding HBase credentials in NetBackup.

The backup hosts use the HBase.conf file to save the configuration settings of the HBase plug-in. You need to create separate file for each backup host and copy it to /usr/openv/netbackup/. You need to create the HBase.conf file in JSON format.

With this release, the following plug-in settings can be configured

Update the BigData policy with the original HMaster name.

See Configuring NetBackup policies for HBase plug-in.