Veritas NetBackup™ for HBase Administrator's Guide

Last Published:
Product(s): NetBackup (8.2, 8.1.2)
Platform: Linux,UNIX,Windows
  1. Introduction
    1.  
      Protecting HBase data using NetBackup
    2.  
      Backing up HBase data
    3.  
      Restoring HBase data
    4.  
      NetBackup for HBase terminologies
    5.  
      Limitations
  2. Deploying HBase plug-in for NetBackup
    1.  
      About the HBase plug-in deployment
    2.  
      Pre-requisites for installing the HBase plug-in
    3.  
      Operating system and platform compatibility
    4.  
      License for HBase plug-in for NetBackup
    5.  
      Preparing the HBase cluster
    6.  
      Best practices for deploying the HBase plug-in
    7.  
      Post installation procedures
    8.  
      Verifying the deployment of the HBase plug-in
  3. Configuring NetBackup for HBase
    1.  
      About configuring NetBackup for HBase
    2. Managing backup hosts
      1.  
        Whitelisting a NetBackup client on NetBackup master server
      2.  
        Configure a NetBackup Appliance as a backup host
    3.  
      Adding HBase credentials in NetBackup
    4. Configuring the HBase plug-in using the HBase configuration file
      1.  
        Configuring NetBackup for a highly-available HBase cluster
    5.  
      Configuration for a HBase cluster that uses Kerberos
    6. Configuring NetBackup policies for HBase plug-in
      1. Creating a BigData backup policy
        1. Creating BigData policy using the NetBackup Administration Console
          1.  
            Using the Policy Configuration Wizard to create a BigData policy for HBase clusters
          2.  
            Using the NetBackup Policies utility to create a BigData policy for HBase clusters
        2.  
          Using NetBackup Command Line Interface (CLI) to create a BigData policy for HBase clusters
    7.  
      Disaster recovery of a HBase cluster
  4. Performing backups and restores of HBase
    1. About backing up a HBase cluster
      1.  
        Pre-requisite for running backup and restore operations for a HBase cluster with Kerberos authentication
      2.  
        Backing up a HBase cluster
      3.  
        Best practices for backing up a HBase cluster
    2. About restoring a HBase cluster
      1. Restoring HBase data on the same HBase cluster
        1.  
          Using the Restore Wizard to restore HBase data on the same cluster
        2.  
          Using the bprestore command to restore HBase data on the same HBase cluster
    3.  
      Restoring HBase data on an alternate HBase cluster
    4.  
      Restoring truncated tables
    5.  
      Best practices for restoring a HBase cluster
  5. Troubleshooting
    1.  
      About NetBackup for HBase debug logging
    2.  
      Backup fails with error 6609
    3.  
      Backup fails with error 6601
    4.  
      Backup fails with error 6623
    5.  
      Restore fails with error 2850
    6.  
      Backup fails with error 20
    7.  
      Backup fails with error 112

Limitations

Review the following limitations before you deploy the HBase plug-in:

  • Only RHEL and SUSE platforms are supported for HBase clusters and backup hosts.

  • HBase plug-in does not capture Extended Attributes (xattrs) or Access Control Lists (ACLs) of an object during backup and hence these are not set on the restored files or folders.

  • For highly available HBase cluster, if fail-over happens during a backup or restore operation, the job fails.

  • If you cancel a backup and restore job manually while the discovery job for a backup operation is in progress, the snapshot entry does not get removed from the HBase web graphical user interface (GUI).

  • HBase plug-in supports HTTP (or non-SSL) configured HBase backup only. Backup job for HBase configured with HTTPS (or SSL) fails.

  • Backup of read-only tables is not supported.

  • You need to add tables one-by-one in the backup selection when you create the backup policy.

  • Table name must not contain underscores.