Guide de client SAN et Fibre Transport VeritasNetBackup™

Configuration des services Fibre Transport sous Linux

1. Exécutez le script nbftsrv_config. Voici un exemple (la sortie dépend du système d'exploitation) :

   /usr/openv/netbackup/bin/admincmd/nbftsrv_config -scst -install
   Checking for SCST drivers and firmwares in the package. [yes]
   Checking whether the server is not NetBackup Appliance. [yes]
   Checking for kernel version 3.10.0-1062. [yes]
   Checking for QLE2692 QLogic 16/32Gb HBA cards on the server. [yes]
   DISCLAIMER:
   -----------
   NOTE:
   1. When you install the SAN client with 16Gb HBA, the script stops the original qla2xxx driver and updates the firmware ql2500_fw.bin. Only QLE2562 and QLE2692 16Gb HBA models are supported by this NetBackup version.
   2. Ensure that there is no other process that uses the HBAs. If there is an active process that uses qla2xxx, manually restart the process after the installation completes.
   3. If you use the SANsurfer agent during the deployment of the environment, the script stops and restarts the SANsurfer agent daemon (qlremote).
   4. Stop all the backup jobs that use the FT user interface.
   
   Do you acknowledge this disclaimer? [y,n] (n)y

2. Les pilotes QLogic sont rechargés de sorte que les ports HBA puissent être détectés pendant cette session.

   Proceeding to deploy SCST environment [ok]
   
   Reload driver qla2xxx
   
   Removing qla2xxx.
   Load driver qla2xxx
   
   HBA-Type Port WWN Status Supported Speeds Current Speed
   QLE2692 21:00:f4:e9:d4:53:bb:c4 Online 8 Gbit, 16 Gbit, 32 Gbit 16 Gbit
   QLE2692 21:00:f4:e9:d4:53:bb:c5 Linkdown 8 Gbit, 16 Gbit, 32 Gbit unknown
   QLE2692 21:00:00:24:ff:16:ce:9c Online 8 Gbit, 16 Gbit, 32 Gbit 16 Gbit
   QLE2692 21:00:00:24:ff:16:ce:9d Linkdown 8 Gbit, 16 Gbit, 32 Gbit unknown
   QLE2562 21:00:00:24:ff:42:2d:78 Linkdown 1 Gbit, 2 Gbit, 4 Gbit, 8 Gbit unknown
   QLE2562 21:00:00:24:ff:42:2d:79 Linkdown 1 Gbit, 2 Gbit, 4 Gbit, 8 Gbit unknown
   
   NOTE:
   The types of HBA cards listed are QLE2692 and QLE2562. Some of the WWNs may be used to connect to an external storage and other external devices.
   
   Do you want to continue? [y,n] (n)y

3. Entrez les numéros de port et vérifiez que les avertissements fonctionnent pendant cette session.

   Please input the Port WWNs you want to use as the targets (separated by commas like: wwn1,wwn2...):21:00:f4:e9:d4:53:bb:c4
   The input is: 21:00:f4:e9:d4:53:bb:c4
   The targets you defined: 21:00:f4:e9:d4:53:bb:c4
   Do you want to redefine the targets? [y,n] (n)
   Do you want to add additional targets? [y,n] (n)
   The targets you defined: 21:00:f4:e9:d4:53:bb:c4
   The targets you have defined contain 16Gb HBA cards.
   
   NOTE:
   1. Make sure that you do not use a WWN that is used to connect to external storage.
   2. Make sure to define the input WWNs as targets.
   3. Make sure the WWNs can be zoned with WWNs of clients.
   Do you want to continue to setup the WWNs as targets? [y,n] (n)y

4. L'environnement FTMS est déployé.

   --------------------------------------------
   FTMS environment installation started.
   --------------------------------------------
   Successfully created the dependent path: /var/lib/scst/pr.
   Successfully created the dependent path: /var/lib/scst/vdev_mode_pages.
   Successfully backup the ql2500_fw.bin to ql2500_fw_original.bin.
   Successfully copied /usr/openv/netbackup/bin/driver/ql2500-firmware-8.04.00.bin to /lib/firmware.
   Successfully copied /usr/openv/netbackup/bin/driver/ql2700-firmware-8.07.10.bin to /lib/firmware.
   Successfully created the new link /lib/firmware/ql2500_fw.bin.
   Successfully created the new link /lib/firmware/ql2700_fw.bin.
   Successfully copied /usr/openv/netbackup/bin/driver/ql2500-firmware-8.04.00-LICENSE to /usr/share/doc/ql2500-firmware-8.04.00.
   Successfully copied /usr/openv/netbackup/bin/driver/scst/qla2xxx.ko.3.10.0-1062.el7.x86_64 to /lib/modules/3.10.0-1062.el7.x86_64/extra/qla2xxx.ko.
   Successfully copied /usr/openv/netbackup/bin/driver/scst/qla2x00tgt.ko.3.10.0-1062.el7.x86_64 to /lib/modules/3.10.0-1062.el7.x86_64/extra/qla2x00tgt.ko.
   Successfully copied /usr/openv/netbackup/bin/driver/scst/scst.ko.3.10.0-1062.el7.x86_64 to /lib/modules/3.10.0-1062.el7.x86_64/extra/scst.ko.
   Successfully copied /usr/openv/netbackup/bin/driver/scst/scst_user.ko.3.10.0-1062.el7.x86_64 to /lib/modules/3.10.0-1062.el7.x86_64/extra/scst_user.ko.
   Successfully created /etc/modprobe.d/qla2xxx_scst.conf.
   Successfully copied /usr/openv/netbackup/bin/nbftsrvr to /usr/openv/netbackup/bin/nbftsrvr_old.
   Successfully copied /usr/openv/netbackup/bin/goodies/nbftserver_scst to /etc/rc.d/init.d/nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc2.d/S21nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc3.d/S21nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc5.d/S21nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc0.d/K03nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc1.d/K03nbftserver.
   Successfully linked /etc/rc.d/init.d/nbftserver /etc/rc.d/rc6.d/K03nbftserver.
   Successfully enabled nbftserver.
   Successfully created /etc/modules-load.d/scst.conf.
   Enable target: 21:00:f4:e9:d4:53:bb:c4
   Previous initramfs image is saved at /boot/initramfs-3.10.0-1062.el7.x86_64.img.07-19-20.22:43:29.
   Running dracut, it may take several minutes to complete...
   /sbin/dracut succeeded
   NetBackup Fibre Transport Server started.
   -------------------------------
   Driver qla2xxx is loaded
   -------------------------------
   Driver qla2x00tgt is loaded
   -------------------------------
   Driver scst is loaded
   -------------------------------
   Driver scst_user is loaded
   --------------------------------------------
   FTMS environment installation completed.