* * * READ ME * * *
                         * * * CPI 7.4.1 * * *
                         * * * Patch 200 * * *
                         Patch Date: 2019-06-04


This document provides the following information:

   * PATCH NAME
   * OPERATING SYSTEMS SUPPORTED BY THE PATCH
   * PACKAGES AFFECTED BY THE PATCH
   * BASE PRODUCT VERSIONS FOR THE PATCH
   * SUMMARY OF INCIDENTS FIXED BY THE PATCH
   * DETAILS OF INCIDENTS FIXED BY THE PATCH
   * INSTALLATION PRE-REQUISITES
   * INSTALLING THE PATCH
   * REMOVING THE PATCH


PATCH NAME
----------
CPI 7.4.1 Patch 200


OPERATING SYSTEMS SUPPORTED BY THE PATCH
----------------------------------------
AIX
RHEL6 x86-64
RHEL7 x86-64
SLES11 x86-64
SLES12 x86-64
Solaris 11 SPARC
Solaris 11 X86



BASE PRODUCT VERSIONS FOR THE PATCH
-----------------------------------
   * InfoScale Availability 7.4.1
   * InfoScale Enterprise 7.4.1
   * InfoScale Foundation 7.4.1
   * InfoScale Storage 7.4.1


SUMMARY OF INCIDENTS FIXED BY THE PATCH
---------------------------------------
Patch ID: 7.4.1.200
* 3969748 (3969438) Rolling upgrade fails when local node is specified at the system name prompt on non-fss environment.
* 3979596 (3979603) While upgrading from InfoScale 7.4.1 to 7.4.1.xxx, CPI installs the packages from the 7.4.1.xxx patch only and not the base packages of 7.4.1 GA.


DETAILS OF INCIDENTS FIXED BY THE PATCH
---------------------------------------
This patch fixes the following incidents:

Patch ID: 7.4.1.200

* 3969748 (Tracking ID: 3969438)

SYMPTOM:
Rolling upgrade fails with the error:
CPI ERROR V-9-0-0
0 Cannot execute _cmd_vxdg list | _cmd_grep enabled | _cmd_awk '{print $1}' on system_name with undefined sys->{padv}

DESCRIPTION:
The following prompt appears as part of the rolling upgrade process: Enter the system name of the cluster on which you would like to perform rolling upgrade [q,?] After the prompt, the installer suggests the names of systems on which to perform the upgrade. You may select one of the suggested system names, or you may type a system name, and then press Enter. Either way, if you specify the system name of the local node, the installer displays the following error and exits.
CPI ERROR V-9-0-0
0 Cannot execute _cmd_vxdg list | _cmd_grep enabled | _cmd_awk '{print $1}' on system_name with undefined sys->{padv}

RESOLUTION:
The installer is enhanced to verify if the fss disk group is available. This enhancements was made for the Linux, Solaris, and Aix platforms.

* 3979596 (Tracking ID: 3979603)

SYMPTOM:
CPI assumes that the third digit in an InfoScale 7.4.1 version indicates a patch version, and not a GA version. Therefore, it upgrades the packages from the patch only and does not upgrade the base packages.

DESCRIPTION:
To compare product versions and to set the type of installation, CPI compares the currently installed version with the target version to be installed. However, instead of comparing all the digits in a version, it incorrectly compares only the first two digits. In this case, CPI compares 7.4 with 7.4.1.xxx, and finds that the first 2 digits match exactly. Therefore, it assumes that the base version is already installed and then installs the patch packages only.

RESOLUTION:
This hotfix updates the CPI to recognize InfoScale 7.4.1 as a base version and 7.4.1.xxx (for example) as a patch version. After you apply this patch, CPI can properly upgrade the base packages first, and then proceed to upgrade the packages that are in the patch.



INSTALLING THE PATCH
--------------------
1. Copy the hot-fix CPI_7.4.1_P2.pl to /tmp
2. Run installation scripts with the hot-fix
   Example:
   ./installer -require /tmp/CPI_7.4.1_P2.pl


REMOVING THE PATCH
------------------
NONE


SPECIAL INSTRUCTIONS
--------------------
NONE


OTHERS
------
NONE