Veritas NetBackup™ Appliance 管理指南

从 Appliance 命令行操作界面开始恢复出厂设置

1. 以管理员身份登录到设备并打开 Appliance 命令行操作界面。
2. 输入 Main_Menu > Support > FactoryReset。此命令将显示以下消息，并且在开始恢复出厂设置之前需要您回答以下问题。

   Appliance factory reset will reset the entire system to the 
   factory installed image. The appliance will have the following components 
   reset to the factory restored settings/image:
   1) Appliance Operating System
   2) Appliance Software
   3) NetBackup Software
   4) Tape device configuration and associated tape images(data) on 
   the primary server
   5) Networking configuration (optionally retain)
   6) Storage configuration and backup data (optionally retain)
   7) Fibre Transport Deduplication target port configuration

   - [Info] Running factory reset validation...please wait (approx 2 mins)
   - [Info] Factory reset validation successful.
   
   RESET NETWORK CONFIGURATION [Optional]
   	-- Resets the IP and routing configuration.
   	-- Resets the DNS configuration.
    >> Do you want to reset the network configuration? [yes/no] (yes) no
   
   RESET STORAGE CONFIGURATION and BACKUP DATA [Optional]

   -- Removes all the images on the AdvancedDisk, MSDP, Share partitions and 
   associated tape images(data).

   -- Resets the storage partitions.
   	-- Resets storage expansion units, if any.
   - [Warning] Performing a factory reset interrupts all share activity and 
     removes and resets all share data. 
     Unmount all the shares on clients before continuing with this operation.
   - [Info] Performing a factory reset removes the current Fibre Transport 
     Deduplication target port configuration.
    >> Do you want to delete images and reset backup data? [yes/no] (yes) yes
    >> Resetting the storage configuration will remove all backup data on the 
       storage partitions and any connected expansion units. This is not reversible. 
       Are you sure you want to reset storage configuration? [yes/no] (yes) yes

3. 回答这些问题之后，将显示“恢复出厂设置摘要”。下面是该摘要的一个示例：

   FACTORY RESET SUMMARY
   ---------------------
   Reset Appliance OS, software configuration          : [YES]
   Reset Appliance network configuration               : [NO]
   Reset Appliance storage configuration (REMOVE DATA) : [YES]

   Appliance will make the following version changes:
   
   +-----------------------------------------------------------------------------+
   |             Appliance             |  Current Version   |  Reverted Version  |
   |-----------------------------------+--------------------+--------------------|
   |appl1                              |NetBackup 10.0      |NetBackup 10.0      |
   |                                   |Appliance 5.0       |Appliance 5.0       |
   +-----------------------------------------------------------------------------+

4. 将显示以下警告。如果要开始恢复出厂设置操作，请输入 Yes。

   WARNING: An appliance factory reset cannot be reversed!
   The reset process takes about 90 minutes. The appliance 
   will be restarted to start the reset process. 
   Do you want to continue? (yes/no) yes"

   恢复出厂设置操作将继续，并会显示信息消息。

5. 必须使用远程管理 端口重新配置网络设置并重新连接到 NetBackup Appliance 网页操作界面。执行以下步骤：

   • 设备重新启动并且在屏幕顶部出现键盘提示后，请点击键盘上的 F2 功能键。

   • 使用键盘上的向左键和向右键导航到 Server Management 菜单。

   • 使用键盘上的向上键和向下键导航到 Baseboard LAN configuration 部分。

   • 选择 RMM4 LAN Configuration 部分。

   • 输入网络配置信息，如 IP 源 [静态]、IP、子网掩码和网关 IP 地址。

   • 现在，您可以连接到设备 NetBackup Appliance 网页操作界面。